GVS CHTC-86/01.1.21 User Manual Download Page 80

Page: 80 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Send telegrams

（

fan coil control

）：

0…100%

fan automatic or fan manual

Fan

1 bit

C, R, T

1.001 DPT_Switch

This communication object is used to switch over fan between auto and manual.

when parameter "Switchover fan between auto and manual" selects "object 'Automatic ON/OFF'",

Send the telegram "1" - fan automatic

Send the telegram "0" - fan manual

when parameter "Switchover fan between auto and manual" selects "object 'Manual ON/OFF'",

Send the telegram "1" - fan manual

Send the telegram "0" - fan automatic

Fan manual stage

Fan

1 byte

C, R, T

5.001 DPT_Scaling

This communication object is used to send the control value of fan manual, to change the wind speed.

Lock temperature control

Temperature

control

1bit

C, R, W

1.001 DPT_Switch

This communication object is used to disable/enable temperature control, including disable/enable basic

heating/cooling control and additional heating/cooling control. When receiving telegram "1", the object "Basic heating /

cooling control value" and object "additional heating / cooling control value" stop sending control telegrams; when

receiving telegram "0", they update control value immediately.

Receive telegram "1" - disable temperature control

Receive telegram "0" - enable temperature control

Note: Stop control telegrams is not restricted by the minimum and maximum control value, if the control

values

are negated, stop control telegrams are negated, too.

Lock additional stage

Temperature

control

1bit

C, R, W

1.001 DPT_Switch

This communication object is used to disable or enable additional heating/cooling control. When receiving telegram

"1", the object "additional heating / cooling control value" stop sending control telegrams; when receiving telegram "0", it

updates control value immediately.

Receive telegram "1" - disable additional heating / cooling control value

Receive telegram "0" - enable additional heating / cooling control value

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands