GVS CHTC-86/01.1.21 User Manual Download Page 75

Page: 75 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

C,T

This communication object is used to receive telegram value from the bus to switch the backlight brightness of backlit

screen.

Received telegram values:

1——the backlight brightness of backlit screen in daytime

0——the backlight brightness of backlit screen at night.

5.2 "Heating/cooling control “Communication Object

Figure 5.2 Temperature control communication object

Object name

Functions

Data Types

Flags

DPT

Input external temperature

Temperature

2 byte

C, R,W

9.001 DPT_Value_Temp

This communication object is for receiving temperature the external temperature sensor sends on the bus.

Actual temperature

Temperature

2 byte

C, R, T

9.001 DPT_Value_Temp

The communication object is used to send the current temperature that is detected by the thermostat panel sensor, to

the bus; the transmission time is set via parameter settings.

When there is an external temperature sensor, the object is used to send the proportion and sum of temperatures sent

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands