GVS CHTC-86/01.1.21 User Manual Download Page 77

Page: 77 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

The communication object is visible when the object type of operating mode is "1bit", and is used to activate standby

mode. Receiving telegram "1"will activate standby mode; receiving telegram "0" will not activate standby mode.

Receive telegram "1"----activate standby mode

Receive telegram "0"----not activate standby mode

Active night mode

Setpoint

temperature

1 bit

C,R,W

1.001 DPT_Switch

The communication object is visible when the object type of operating mode is "1bit", and is used to activate night

mode. Receiving telegram "1"will activate night mode; receiving telegram "0" will not activate night mode.

Receive telegram "1"----activate night mode

Receive telegram "0"----not activate night mode

Active frost/heat protection

mode

Setpoint

temperature

1 bit

C, R,W

1.001 DPT_Switch

The communication object is visible when the object type of operating mode is "1bit", and is used to activate the frost

/heat protection mode. Receiving telegram "1"will activate the frost /heat protection mode; receiving telegram "0" will not

activate the frost /heat protection mode.

Receive telegram "1"----activate the frost /heat protection mode

Receive telegram "0"----not activate the frost /heat protection mode

Temperature operating mode

switchover

Setpoint

temperature

1 byte

C, R,W

20.102 DPT_HVACMode

The communication object is visible when the object type of operating mode is "1bit", and is used to switch to RTC

mode. Different telegrams mean different operating modes, as follows: 0: Auto (comfortable), 1: comfort mode, 2: Standby

mode, 3: Night Mode, 4: Frozen protection /heat protection, 5~255: Reserved, do not use. For example, when an object

receives a telegram "2", the thermostat panel will control the actuator according to the standby mode setting.

Communication object of operating mode switching has priority; thermostat panel activates the operating mode

according to the priority of a communication object of operating mode. More information is seen in 4.4 "Object type for

operating mode switchover".

Heating/cooling switchover

Temperature

control

1bit

C, R, W

1.100 DPT_Heat/Cool

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands