GVS CHTC-86/01.1.21 User Manual Download Page 61

Page: 61 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Parameter "Limit number of Tele."

Options: yes

This parameter sets limits on the number of binary input telegrams sent to the main bus, in order to

reduce the burden of bus. If selecting "Yes", the parameter "Max. Number Tele. Within a period" is

visible.

Parameter "Max. Number Tele. Within a period"

Options: 30/60/100/127

This parameter sets the number of telegrams can be sent in a maximum of 17 seconds.

Bus voltage is restored, the device initialization is complete, the timer starts and starts counting

telegrams, once the maximum allowed number of telegrams sent once reached, then no telegrams will

be sent to the bus until the end of 17 seconds. After the end of the 17 seconds, the timer re-starts, and

the telegram restarts to count.

Parameter "Function of input 1"

Options: No function

Switch

Switch/Dimming

Shutter control

Scene

This parameter sets functions of binary inputs.

4.12.1

Switch

In parameter window "Input 1/2/3", select "Switch" in "Function of input 1 /2/3", seen in Figure

4.12.2.

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands