GVS CHTC-86/01.1.21 User Manual Download Page 25

Page: 25 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Figure 4.4.3 Parameter setting interface of “Heating/cooling setpoint”

Parameter “operation mode after reset”

Options

：

comfort

standby

night

Frost/heat protection

Here we can set the work patterns which is after BUS DEVICE RESET or after programming.

There are 4 work patterns in temperature controller including comfort mode, standby mode, night

mode and Frost/Heating protecting mode. Every mode has its corresponding temperature setting.

Comfort mode is applied to the daytime when someone at home. Standby mode is applied to the

daytime when no one at home for saving the energy. Night mode is applied for the night time when

someone at home. Frost/Heating protecting mode is applied for the long time going out in order to

prevent the devices from damaging by the highest or lowest temperature.

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands