GVS CHTC-86/01.1.21 User Manual Download Page 16

Page: 16 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

If you choose "no", conduct day or night light switch through the communication objects-"Day / night

mode"; If you choose "yes”, setting up automatic switching by setting the time moment.

Parameter "Time for switching to night at: hour (0 ... 23) / minute (0 ... 59)"

Set the time that LCD backlight brightness switches to night backlight. For example, once setting to

18:00 that means the backlight brightness of the LCD screen automatically switches to night mode when

the time is 18:00 pm.

Parameter "Time for switching to day at: hour (0 ... 23) / minute (0 ... 59)"

Set the time that LCD backlight brightness of the backlight switch to daylight. For example, once

setting to 6:00, that means LCD backlight brightness automatically switched to day mode when the time

is 6:00.

Parameter "Time mode"

Options: 24H

AM / PM

This parameter set show the mode of time display. "24H" indicates the time on the Thermostat

display system for 24 hours; "AM / PM", means the time display system in Thermostat for 12-hour.

Parameters "Send current time"

Options: Do not send

30s

1min

30min

This parameter set sends the current time on the bus, "Do not send" means don't send time to the

bus; "1s" means sending the time to the bus per second; "30s" means sending time to the bus on 30s,

such as 9:10:30, 9:11:30, 9:12:30; "1min" means sending the time to the bus per on minute point, such

9:11:00, 9:12:00, 9:13:00

; "30min" means sending the time to the bus on 30 minutes, such as

9:30:00,

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands