GVS CHTC-86/01.1.21 User Manual Download Page 49

Page: 49 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Send the same telegram as upper threshold

This parameter sets the action when the threshold value is banned.

Select “do not send", no action;

Select "Send the same telegram as lower threshold", when the object "temperature threshold

value1/2 block" receives telegram "1", the object "1bit/1byte output, temperature" sends the same

telegram as lower threshold.

Select "Send the same telegram as upper threshold", when the object "temperature threshold

value1/2 block" receives telegram "1",the object"1bit/1byte output, temperature"sends the same

telegram as upper threshold

This parameter can be seen in "use block of the temperature threshold output" if User selects "yes".

Parameter "Behaviour when releasing the lock"

Options: Do not send

Update

This parameter sets the action when the threshold value is started again.

Select "do not send", when the object "temperature threshold value1/2 block" receives the telegram

"0", if the threshold value changes, “1bit/1byte output, temperature” value will be sent immediately, but

not vice versa. If the current temperature is between high and low thresholds, no telegram will be sent; if

loop sending is enabled, the previous telegram will be loop sent.

Select "update", when the object "temperature threshold value1/2 block" receives

telegram "0",

the object "1bit/1byte output, temperature" updates according to the threshold range of the current

temperature, no matter whether the object value changes, the telegram is sent. If the current

temperature is between the high and low thresholds, the object value cannot be determined, the

telegram is not sent, even though in case of sending cyclically.

This parameter can be seen in "use block of the temperature threshold output" if User selects "yes".

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands