GVS CHTC-86/01.1.21 User Manual Download Page 82

Page: 82 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

This communication object would display when parameter

”

Setpoint adjustment

”

Selects “absolute adjustment”, it is used to

modify the heat protection mode temperature at cooling

5.3 "Threshold value" communication object

Figure 5.3 Threshold value communication object

Number

Object name

Functions

Data Types

Flags

DPT

27/31

Chang temperature threshold

value 1/2

Temperature threshold value 1/2

2byte

C, R, W

9.001

DPT_Value_Temp

This communication object is used to change the temperature's high threshold value.

Telegram:

0…50

℃

28/32

1 bit output temperature

Temperature threshold value 1/2

1bit

C, R,T

1.001 DPT_Switch

When the temperature is higher than the current high threshold or below the low threshold, 1bit telegram can be sent via this

object to the bus, specific telegrams can be set by the parameter "logic 1bit telegram value [0 ... 1]".

29/33

1 byte output temperature

Temperature threshold value 1/2

1byte

C, R,T

5.010

DPT_Value_1_Ucount

When the temperature is higher than the current high threshold or below the low threshold, 1bit telegram can be sent via this

object to the bus, specific telegrams can be set by the parameter "1byte telegram value[0…255]".

30/34

Temperature threshold value

1/2 block

Temperature threshold value 1/2

1bit

C, R,W

1.001 DPT_Switch

This communication object is used to disable or enable the function of the temperature threshold value. Disabled and enabled

actions can be set by the parameter.

Receive telegram "1" - disable the temperature threshold value

Receive telegram "0" - enable the temperature threshold value

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands