FujiFilm ED-580XT Operation Manual Download Page 9 | Manualshive

Page: 9 / 136

background image

897N200877B

1

Introduction

Introduction

This chapter explains about this manual.

About This Manual

This manual provides necessary information for using this product, such as the equipment
overview, operation procedures and precautions to observe. In addition, the Reprocessing
Manual supplied with this product describes the reprocessing and storage methods for the
endoscope. This manual does not provide information about procedures or any aspects of
endoscopic techniques.

Before using this product, thoroughly read and understand this manual, the Reprocessing
Manual and the manual of related equipment and use this product as instructed.
Also, after reading this manual, store it close to this product for future reference to keep this
product in optimum working condition.

If you have any questions or comments about any information in this manual, contact your
local FUJIFILM dealer.

This manual may not be reproduced in whole or in part in any form without prior permission.
The information contained in this manual may be subject to change without prior notice.

Trademarks

The company names and product names described in this manual are trademarks or registered trademarks of

FUJIFILM Corporation or its subsidiaries.
Other holders’ trademarks

All other company names and product names described in this manual are trademarks or registered trademarks of

their respective owners.

Copyright © 2018 FUJIFILM Corporation. All rights reserved.

ED580XT_E2-30_897N200877B.indb 1

2018/09/20 15:50:16

«
...
7
8
9
10
11
...
»

Summary of Contents for ED-580XT









































































































































Reviews:

No comments

Related manuals for ED-580XT

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: York Fitness Pages: 20

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: Yetter Pages: 24

ABS-Lock III-BE

Brand: ABS Pages: 8

AutoMate 2500 series

Brand: Beckman Coulter Pages: 50

Brand: Grundig Pages: 16

Pacific FITNESS Solana

Brand: Precor Pages: 35

ZiXpress 64 DX system

Brand: ZINEXTS Pages: 34

Brand: Lakeland Pages: 16

Brand: Event Lighting Pages: 7

Brand: OttLite Pages: 2

Brand: Rohde & Schwarz Pages: 36

MicroVention MCS-18

Brand: Terumo Pages: 104

Brand: Defibtech Pages: 12

Brand: ICE COBOTICS Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands