Foma P702i, Manual

Page: 476 / 478

38
※ The following commands do not result in an error even if specified; however, they do not function as commands.
ATS5=n
[M]
[&F]
Sets the back space (BS)
character. n=8: Default (n=8 only specifiable.)
ATS5?: Inquires the set value.
ATS5=8
OK
ATS5?
008
OK
ATS7=n
[M]
[&F][&W]
Sets standby duration until
connection is complete.
Disconnects the line if an
outgoing call is not connected
within the specified time. n=1 to 120 (default=60) (unit: second)
121 to 255 are assumed to be 120 if specified.
ATS7?: Inquires the set value.
ATS7=60
OK
ATS7?
060
OK
ATS30=n
[M][&F]
Sets the inactive timer (minute).
When no user data is sent or
received, the connection is cut
after the set time. This command
is for only 64K data
communication. When 0 is set,
the inactive timer turns to OFF. n=0 to 255 (default=0) (unit: minute) ATS30=0
OK
ATS103=n
[M][&F]
Selects characters to pause for
incoming sub-address. n=0:
_
(asterisk)
n=1: / (slash) (default)
n=2: ¥ or back slash
ATS103=0
OK
ATS104=n
[M][&F]
Selects characters to pause for
outgoing sub-address. n=0: # (sharp)
n=1: % (percentage) (default)
n=2: & (and) ATS104=0
OK
ATVn
[M]
[&F][&W] Sets all the result codes in the
numeric or alphabetical notation. n=0: Returns the result code in a numeric value.
n=1: Returns the result code in alphabetical characters.
(default)
ATV1
OK
ATXn
[M]
[&F][&W]
Sets whether to display the
speed in the CONNECT display
at connection.
Detects busy tone and dial tone. n=0: Dial tone not detected; busy tone not detected;
speed not displayed.
n=1: Dial tone not detected; busy tone not detected;
speed displayed.
n=2: Dial tone detected; busy tone not detected; speed
displayed.
n=3: Dial tone not detected; busy tone detected; speed
displayed.
n=4: Dial tone detected; busy tone detected; speed
displayed. (default)
ATX1
OK
ATZ
[M]
Resets the setting to the
contents of the nonvolatile
memory. If this command is
entered during communication,
the line is disconnected.
−
(In online)
ATZ
NO CARRIER
(In offline)
ATZ
OK
AT¥S
[M]
Displays the contents of the each
command and S register
currently set.
−
AT¥S
E1 Q0 V1 X4 &C1
&D2 &S0 ¥V0
S000=000
S002=043
S003=013
S004=010
S005=008
S006=005
S007=060
S008=003
S010=001
S030=000
S103=000
S104=000
OK
AT¥Vn
[M]
[&F][&W] Selects the response code
specifications at connection. n=0: Does not use the extended result code. (default)
n=1: Uses the extended result code. AT¥V0
OK
･ AT (AT only entered.)
･
ATP (Pulse setting)
･ ATS8 (Setting the pause time by comma dialing)
･ ATT (Tone setting)
･
ATS6 (Setting the pause time taken for dialing)
･ ATS10 (Setting the automatic disconnection delay time)
AT command Outline Parameter/Explanation
Command execution
example