Foma P702i, Manual

Page: 339 / 478

336
Other Useful Function
s
Cal
l Data
You can confirm the last and accumulated call duration and
cost for calls.
p
Displayed call duration and cost are for reference and might differ
from the actual ones. In addition, the consumption tax is not
included in the call cost.
p
Both the voice call duration and digital communications duration
(video-phone call d64K data communication duration) are
displayed and both incoming and outgoing calls are included in the
duration.
p Call cost is only for the dialed calls. However, “¥0” or “¥ __ ” is
displayed for toll free call, Directory Assistance Service (104), etc.
p Call cost is accumulated on the UIM. Therefore, when you replace
the UIM, the charge accumulated on the UIM in use is displayed.
(accumulation from December 2004)
※ You cannot display the accumulated cost on the UIM using the
FOMA phones that were released before the 901i series. (The cost
is accumulated on the UIM.)
p You can reset the displayed call duration and call cost.
1
Call time/cost Call data
L ast call duration . . . . . . Talk: Displays the call duration of the
latest voice call.
Digital: Displays the call duration of the
latest video-phone call and 64K data
communication.
Last call cost . . . . . . . . . Talk: Displays the call cost for the latest
voice call.
Digital: Displays the call cost for the latest
video-phone call and 64K data
communication.
Total calls duration . . . . Talk: Displays the call duration of voice
call from the time Reset Total
Duration was executed until the
current time.
Digital: Displays the call duration of
video-phone call and 64K data
communication from the time Reset
Total Duration was executed until
the current time.
Total calls . . . . . . . . . . . Displays the call cost from the time Reset
Total Cost was executed to the current
call.
Calls reset . . . . . . . . . . . Displays the date and time when Reset
Total Duration was executed last time.
Cost reset . . . . . . . . . . . Displays the date and time when Reset
Total Cost was executed last time.
p
After checking, press .
Call Data
Checking Call Duration and Cost
< >
Information
p
When the date and time are not set, or if “Reset total cost&dura.” has
not been done after setting the date and time, the date and time of Calls
Reset and Cost Reset are not displayed.
p
When Last Call Duration exceeds “19 hours 59 minutes 59 seconds”, or
Total Calls Duration exceeds “199 hours 59 minutes 59 seconds”, “0 s”
returns to re-count the time.
p
The total calls duration for video-phone calls is the digital
communication, so it is displayed in “Digital” not in “Talk”.
p If you switch between the voice call and video-phone call during a call,
the call duration and call cost are counted respectively for the calls. You
are not charged while “Changing” (see page 58 and page 85) is
displayed.
p The duration/charge for PushTalk, i-mode communication and packet
communication are not counted. For how to check i-mode bill, refer to
“i-mode Operation Guide” which is supplied on your i-mode contract.
p The duration for ringing and calling is not counted as call duration.
p
If you turn off the power or remove the UIM, Last Call Duration is reset
to “0 s”; and Last Call Cost is reset to “¥
__ ”.
1
Call time/cost Reset total
cost&dura. Enter your Terminal Security
Code Do the following operations.
You can set the call cost limit for Total Calls and can be
notified when it is exceeded. If you set “Auto reset
setting” to “ON”, the call cost is reset at midnight on the
1st of the month and “
” is deleted.
1
Call time/cost
Notice call cost
Enter your Terminal Security Code
ON or OFF
p If you select “OFF”, the setting is completed.
2
Enter a maximum cost
You can set from ¥10 through ¥100,000 in unit of ¥10.
p If you do not change Max Cost, just press without entering
the maximum cost.
3
Select a method to alert ON or OFF
Enter the PIN2 code
p See page 154 for PIN2 code.
You can clear “ ” displayed by Notice Call Cost.
1
Call time/cost
CLR max cost icon
Enter your Terminal Security Code
Reset Total Cost&Duration
Resetting Total Duration/Total Cost
< >
Item Operations
Reset total duration You can reset Last Call Duration and Total Calls
Duration to “0 s”.
YES
Reset total cost You can reset Last Call Cost and Total Calls to
“¥0”.
YES Enter the PIN2 code
p
See page 154 for PIN2 code.
Notice Call Cost
Setting Call Cost Limit
Setting at purchase
Notice call cost: OFF
Max cost: ¥0 (when “Notice call cost” is set
to “ON”)
Method to alert: Icon (when “Notice call
cost” is set to “ON”)
Auto reset setting: OFF (when “Notice call
cost” is set to “ON”)
< >
■ When Total Calls has exceeded Max Cost:
“ ” appears. When “Icon + alarm” is set as a notice method and the
Stand-by display returns, the message to the effect that the call cost has
exceeded the maximum cost is displayed, and a warning tone sounds
from the speakers.
Clear Max Cost Icon
＊
You need to obtain a miniSD memory card separately to use the functions related to the miniSD memory card. (See page 312)