Endress+Hauser Proline Promag 55 Operating Manual Download Page 38 | Manualshive

Page: 38 / 130

background image

6 Block TOTALIZER

Device Functions Proline Promag 55 FOUNDATION Fieldbus

38

Hauser

6.1.2

Function group OPERATION

TOTALIZER

D

⇒

TOTALIZER 1

DAA

⇒

CONFIGURATION

300

⇓

⇓

OPERATION

304

TOTALIZER 2

DAB

⇒

CONFIGURATION

300

⇓

⇓

OPERATION

304

TOTALIZER 3

DAC

⇒

CONFIGURATION

300

⇓

OPERATION

304

Function description

TOTALIZER

→

TOTALIZER (1 to 3)

→

OPERATION

The function descriptions below apply to Totalizers 1 to 3; the Totalizers are independently configurable.

SUM
(3040)

Use this function to view the total for the totalizer's measured variable aggregated since
measuring commenced. The value can be positive or negative, depending on the setting
selected in the "TOTALIZER MODE" function (3002), and the direction of flow.

User interface:

Max. 7-digit floating-point number, including sign and unit
(e.g. 15467.04 m

3

; –4925.631 kg)

!

Note!

• The effect of the setting in the "TOTALIZER MODE" function (

follows:
– If the setting is "BALANCE", the totalizer balances flow in the positive and negative

directions.

– If the setting is "FORWARD", the totalizer registers only flow in the positive

direction.

– If the setting is "REVERSE", the totalizer registers only flow in the negative

direction.

• The totalizer's response to faults is defined in the "FAILSAFE ALL TOT" function

(3801), (

OVERFLOW
(3041)

Use this function to view the overflow for the totalizer aggregated since measuring
commenced.

Total flow quantity is represented by a floating-point number consisting of max. 7 digits.
You can use this function to view higher numerical values (> 9,999,999) as overflows.
The effective quantity is thus the total of OVERFLOW plus the value returned by the
SUM function.

Example:
Reading for 2 overflows: 2

⋅

10

7

dm

3

(= 20000000 dm

3

)

The value displayed in the function SUM = 196845.7 dm

3

Effective total quantity = 20196845.7 dm

3

User interface:

Integer with exponent, including sign and unit, e.g. 2

⋅

10

7

dm

3

«
...
36
37
38
39
40
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: QUIETON Pages: 24

Brand: Quest Engineering Pages: 24

Brand: Nauticam Pages: 2

Brand: Samsung Pages: 21

Brand: Xplova Pages: 13

projectorsleeve

Brand: 3M Pages: 14

Brand: 3LeggedThing Pages: 9

Brand: Hama Pages: 40

Brand: Rave Sports Pages: 16

Brand: BAFANG Pages: 4

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Vello Pages: 12

Brand: Perenio Pages: 39

Brand: Calex Pages: 16

Brand: Trailboss Pages: 8

Brand: Waeco Pages: 168

Brand: S&S Northern Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands