Endress+Hauser Proline Promag 55 Operating Manual Download Page 55 | Manualshive

Page: 55 / 130

background image

Device Functions Proline Promag 55 FOUNDATION Fieldbus

8 Block SUPERVISION

Hauser

55

8.1.2

Function group OPERATION

SUPERVISION

J

⇒

SYSTEM

JAA

⇒

CONFIGURATION

800

⇓

OPERATION

804

Function description

SUPERVISION

→

SYSTEM

→

OPERATION

ACTUAL
SYSTEM CONDITION
(8040)

Use this function to check the present system condition.

User interface:

SYSTEM OK or the fault/notice message with the highest priority.

PREVIOUS SYSTEM
CONDITIONS
(8041)

Use this function to view the fifteen most recent fault and notice messages since
measuring last started.

User interface:

The 15 most recent error or notice messages

SIMULATION
FAILSAFE MODE
(8042)

Use this function to set the Analog Input and Totalizer function blocks to their defined
flow response modes in order to check whether they respond correctly. During this time,
message no. 692 "SIM. MEASURAND" appears on the display.

Options:

OFF
ON

Factory setting:

OFF

!

Note!

With the fieldbus, an active simulation is relayed to downstream function blocks and
higher-order control systems by means of the status "UNCERTAIN" of the output value
OUT (AI Block).

SIMULATION
MEASURAND
(8043)

Use this function to set all inputs, outputs and totalizers to their defined flow response
modes in order to check whether they respond correctly. During this time, the words
"SIMULATION MEASURAND" appear on the display.

Options:

OFF
MASS FLOW
VOLUME FLOW

Factory setting:

OFF

"

Caution!

• The measuring device cannot be used for measuring while this simulation is in

progress.

• The setting is not saved if the power supply fails.

«
...
53
54
55
56
57
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Federal Signal Corporation Pages: 13

Brand: Hammond Pages: 754

Brand: 4B Pages: 16

Brand: Lastolite Pages: 3

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: dol sensors Pages: 4

PECOS Universal

Brand: Speed Link Pages: 4

scanCONTROL 25 100 Series

Brand: MICRO-EPSILON Pages: 60

Extreme Racing 15

Brand: Odyssey Pages: 4

Brand: Cerlic Pages: 20

Brand: Bison Pages: 3

Brand: Thule Pages: 8

Brand: ECS Electronics Pages: 16

Brand: Mad4One Pages: 5

PREST-O-LITE 02X93

Brand: ESAB Pages: 2

Brand: Mechatron Pages: 60

Brand: IFM Pages: 17

Brand: QUNDIS Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands