Endress+Hauser Proline Promag 55 Operating Manual Download Page 58

Page: 58 / 130

8 Block SUPERVISION

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

8.2.3

Function group AMPLIFIER

8.2.4

Function group F-CHIP

SUPERVISION

⇒

SYSTEM

JAA

⇓

VERSION INFO

JCA

⇒

DEVICE

810

⇓

SENSOR

820

⇓

AMPLIFIER

822

Function description

SUPERVISION

→

VERSION INFO

→

AMPLIFIER

SOFTWARE REVISION
NUMBER AMPLIFIER
(8222)

Use this function to view the software revision number of the amplifier.

SOFTWARE
REVISION NUMBER
T-DAT
(8225)

Use this parameter to view the software revision number of the software used to create
the content of the T-DAT.

LANGUAGE GROUP
(8226)

Use this function to view the language group.

The following language groups can be ordered: WEST EU / USA, EAST EU / SCAND.,
ASIA, CHINA.

User interface:

available language group

Note!

• The language options of the available language group are displayed in the LANGUAGE

(2000) function.

• You can change the language group via the configuration program ToF Tool - Fieldtool

Package. Please do not hesitate to contact your Hauser sales office if you have
any questions.

SUPERVISION

⇒

SYSTEM

JAA

⇓

VERSION INFO

JCA

⇒

DEVICE

810

⇓

SENSOR

820

⇓

AMPLIFIER

822

⇓

F-CHIP

824

Function description

SUPERVISION

→

VERSION INFO

→

F-CHIP

STATUS F-CHIP
(8240)

Use this function to check whether an F-CHIP is installed and which software options are
available.

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands