Endress+Hauser Proline Promag 55 Operating Manual Download Page 56

Page: 56 / 130

8 Block SUPERVISION

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

VALUE SIMULATION
MEASURAND
(8044)

Note!

The function is not visible unless the SIMULATION MEASURAND function (8043) is
active.

Use this function to specify a selectable value (e.g. 12 m

/s). This is used to test the

associated functions in the device itself and downstream signal loops.

User input:

5-digit floating-point number [unit]

Factory setting:

0 [unit]

Caution!

• The setting is not saved if the power supply fails.
• The appropriate unit is taken from the function group SYSTEM UNITS (ACA),

(

→

Page 11).

SYSTEM RESET
(8046)

Use this function to perform a reset of the measuring system.

Options:

NO
RESTART SYSTEM (restart without interrupting power supply)

Factory setting:

OPERATION HOURS
(8048)

Use this function to view the hours of operation of the device.

User interface:

Depends on the number of hours of operation elapsed:
Hours of operation <10 hours

→

display format = 0:00:00 (hr:min:sec)

Hours of operation 10 to 10000 hours

→

display format = 0000:00 (hr:min)

Hours of operation >10000 hours

→

display format = 000000 (hr)

Function description

SUPERVISION

→

SYSTEM

→

OPERATION

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands