Endress+Hauser Proline Promag 55 Operating Manual Download Page 11 | Manualshive

Page: 11 / 130

background image

Device Functions Proline Promag 55 FOUNDATION Fieldbus

3 Block MEASURED VARIABLES

Hauser

11

3.2

Group SYSTEM UNITS

3.2.1

Function group

CONFIGURATION

MEASURED

VARIABLES

A

⇒

MEASURING VALUES

AAA

⇓

SYSTEM UNITS

ACA

⇒

CONFIGURATION

040

Function description

MEASURED VARIABLES

→

SYSTEM UNITS

→

CONFIGURATION

You can select the units for measured variables in this function group.

!

Note!

The units selected here have no effect on the fieldbus. They are only used for the local display and for assigned
instrument functions.

UNIT MASS FLOW
(0400)

Use this function to select the unit for displaying the calculated mass flow (mass/time).
The mass flow is derived from the preset (compensated) specific fluid density and the
measured volume flow.

The unit you select here is also valid for:
• Low flow cut off

Options:

Metric:
Gram

→

g/s; g/min; g/h; g/day

Kilogram

→

kg/s; kg/min; kg/h; kg/day

Metric ton

→

t/s; t/min; t/h; t/day

US:
Ounce

→

oz/s; oz/min; oz/h; oz/day

Pound

→

lb/s; lb/min; lb/h; lb/day

Ton

→

ton/s; ton/min; ton/h; ton/day

Factory setting:

Nominal diameter and country dependent

UNIT MASS
(0401)

Use this function to select the unit for displaying the calculated mass. The mass is derived
from the preset (compensated) specific fluid density and the measured volume.

Options:

Metric

→

g; kg; t

US

→

oz; lb; ton

Factory setting:

Nominal diameter and country dependent

!

Note!

The unit for the totalizers is independent of your choice here.
The unit for each totalizer is selected separately for the totalizer in question.

«
...
9
10
11
12
13
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Davis Instruments Pages: 16

CYCLO 315 Series

Brand: Magellan Pages: 39

Brand: MadStad Engineering Pages: 2

Brand: Parker Pages: 2

Brand: Park Tool Pages: 2

Brand: ParaZero Pages: 17

Brand: Vaisala Pages: 24

Brand: Waterpik Pages: 20

Water Flosser WF-06

Brand: Waterpik Pages: 2

Brand: Waterpik Pages: 6

Brand: Waterpik Pages: 24

Brand: AirTest Pages: 4

Brand: Flymo Pages: 24

Brand: Kingpin Pages: 4

Brand: Miller Pages: 18

Brand: Varec Pages: 70

Sagewash Sanitizer

Brand: Sage Pages: 2

Brand: Recsea Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands