Endress+Hauser Proline Promag 55 Operating Manual Download Page 82 | Manualshive

Page: 82 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

82

Hauser

Sys. - Positive Zero
Return

AUTO - OOS

Use this parameter to interrupt evaluation of measured variables. This is
necessary when a piping system is being cleaned, for example. This setting
acts on all parameter and calculations of the measuring device.

Options:

OFF (signal output not interrupted)
ON (signal output is set to the value for "Positive zero return" or "Zero
flow")

Factory setting:

OFF

!

Note!

• If positive zero return is active, a flow value of "0" is output via the

output value OUT (AI Block).

• Active positive zero return is relayed to downstream function blocks or

higher-order process control systems by means of the status
UNCERTAIN of the output value OUT (AI Block).

• Positive zero return can also be controlled using cyclic data transfer via

the Discrete Output function block.

Sys. - Special Filter

AUTO - OOS

There is the option of activating two signal filters in this parameter. These
filters make it possible to either suppress the signal caused by severely
fluctuating flows (STANDARD option) or to reproduce it completely –
both on the display and on the FOUNDATION Fieldbus output
(DYNAMIC FLOW option).

Options:

STANDARD
For signal output with normal, stable flow.

DYNAMIC FLOW
For signal output with severely fluctuating or pulsating flow.

Factory setting:

STANDARD

"

Caution!

• The signal behavior on the outputs also depends on the

"Sys. - Flow Damping" parameter.

• Additional filter settings (e.g. STANDARD CIP or DYNAMIC FLOW

CIP) can only be selected using a special service code. Such settings
that are mostly made by a service technician are deleted again if the
customer code is entered anew and can then no longer be activated.

Sys. - CIP Samples

AUTO - OOS

This parameter is only used in the event of a service call.

Sys. - Permanent
Storage

read only

This parameter indicates whether permanent saving of all parameters in
the EEPROM is switched on or off.

User interface:

OFF
ON

Factory setting:

ON

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
80
81
82
83
84
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Palm Pages: 14

Brand: Toco Pages: 12

Brand: Xenith Pages: 17

Brand: zenitech Pages: 16

Brand: IFM Electronic Pages: 16

Brand: IFM Electronic Pages: 6

Brand: YUNEEC Pages: 10

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: Wetekom Pages: 19

Brand: Becker Pages: 52

Brand: Kubota Pages: 11

RideAlong Lite 100109

Brand: Thule Pages: 12

Brand: IFM Electronic Pages: 21

Brand: Acebil Pages: 11

Brand: Oliver Bonas Pages: 2

VXI/VMEpc 600 series

Brand: National Instruments Pages: 61

Brand: Yeti Pages: 13

echoflex OWS-DT-UW-120/277

Brand: ETC Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands