Endress+Hauser Proline Promag 55 Operating Manual Download Page 88 | Manualshive

Page: 88 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

88

Hauser

Sensor Data -
Zero Point

AUTO - OOS

Use this function to view the current zero-point correction value for the
sensor.
Zero-point correction is determined and set at the factory.

User interface:

Max. 4-digit number: –1000 to +1000

Factory setting:

Depends on nominal diameter and calibration

Sensor Data -
Nominal Diameter

AUTO - OOS

Use this function to view the nominal diameter of the sensor. The nominal
diameter depends on the size of the sensor and is set at the factory.

User interface:

2 to 2000 mm or 1/12 to 78"

Factory setting:

Depends on the size of the sensor

Sensor Data -
Measuring Period

AUTO - OOS

Use this function to view the measuring period. The duration of the
measuring period is calculated from the rise time of the magnetic field, the
brief recovery time, the integration time and the empty pipe detection
time.

User interface:

Max. 4-digit number: 10 to 1000 ms

Factory setting:

Depends on nominal diameter

!

Note!

The system checks the time entered and sets the measuring period which
is actually used internally to a plausible value. If you enter 0 ms, the
system automatically computes the shortest time.

Simulation -
Measurand

AUTO - OOS

Use this parameter to activate the simulation of the volume flow/mass
flow.

Options:

OFF
VOLUME FLOW
MASS FLOW

Factory setting:

OFF

"

Caution!

• The measuring device cannot be used for measuring while this

simulation is in progress.

• The simulation acts independently of the position of the jumpers on the

I/O board (

→

see Operating Instructions for Proline Promag 55

FOUNDATION Fieldbus, BA126D).

• The setting is not saved if the power supply fails.

!

Note!

Active simulation is relayed to downstream function blocks or higher-
order process control systems by means of the status UNCERTAIN of the
output value OUT (AI Block).

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
86
87
88
89
90
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Super G3 FAX Board-T1

Brand: Canon Pages: 16

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Canon Pages: 6

7215 - LV XGA LCD Projector

Brand: Canon Pages: 8

Brand: Walimex Pro Pages: 4

Brand: KARPO Fly Pages: 13

Formula F732 WIZARD

Brand: Datalogic Pages: 2

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: Manfrotto Pages: 2

Brand: Manfrotto Pages: 2

Brand: Mammut Pages: 32

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Datapath Pages: 16

Merrytec MK054V RC Series

Brand: V-TAC Pages: 105

Brand: Brodit Pages: 2

FT2A-PWR-IT Series

Brand: Crestron Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands