Endress+Hauser Proline Promag 55 Operating Manual Download Page 107

Page: 107 / 130

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

107

Info Line Mux -
Display Mode

AUTO - OOS

Note!

The option is not active unless one of the following was selected in the
parameter "Info Line Mux - Assign" (

→

Page 105):

• MASS FLOW BARGRAPH IN %
• VOLUME FLOW BARGRAPH IN %

Use this parameter to define the format of the bar graph.

Options:

STANDARD (Simple bar graph with 25 / 50 / 75% gradations and
integrated sign).

A0001258

SYMMETRY (Symmetrical bar graph for positive and negative directions of
flow, with –50 / 0 / +50% gradations and integrated sign).

A0001258

Factory setting:

STANDARD

"Display" Transducer Block/base index 1800:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands