Endress+Hauser Proline Promag 55 Operating Manual Download Page 18 | Manualshive

Page: 18 / 130

background image

4 Block QUICK SETUP

Device Functions Proline Promag 55 FOUNDATION Fieldbus

18

Hauser

4.2

Data backup/transmission

Using the T-DAT SAVE/LOAD function, you can transfer data (device parameters and settings)
between the T-DAT (exchangeable memory) and the EEPROM (device storage unit).

This is required in the following instances:
• Creating a backup: current data are transferred from an EEPROM to the T-DAT.
• Replacing a transmitter: current data are copied from an EEPROM to the T-DAT and then

transferred to the EEPROM of the new transmitter.

• Duplicating data: current data are copied from an EEPROM to the T-DAT and then transferred to

EEPROMs of identical measuring points.

!

Note!
Installing and removing T-DAT

→

See Operating Instructions for Proline Promag 55

FOUNDATION Fieldbus.

a0001221-en

Data backup/transmission with T-DAT SAVE/LOAD function

Information on the LOAD and SAVE options available:

LOAD: Data are transferred from the T-DAT to the EEPROM.

!

Note!
• Any settings already saved on the EEPROM are deleted.
• This option is only available if the T-DAT contains valid data.
• This option can only be executed if the software version of the T-DAT is the same or newer than

that of the EEPROM. Otherwise, the error message "TRANSM. SW-DAT" appears after restarting
and the LOAD function is then no longer available.

SAVE:
Data are transferred from the EEPROM to the T-DAT.

F

Esc

E

+

-

XXX.XXX.XX

F

F

F

F

F

F

P

P

P

P

N

O

T-DAT

SAVE/LOAD

Quick Setup

HOME

POSITION

LOAD

YES

NO

CANCEL

SAVE

YES

NO

Restart of the

measuring device

Input is

saved

«
...
16
17
18
19
20
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: GDC Pages: 64

Brand: DataSafe Pages: 4

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

Brand: EarthX Pages: 17

Brand: EarthX Pages: 23

Brand: RAKINDA Pages: 20

Brand: ZALMAN Pages: 20

Brand: Oki Pages: 18

Brand: Zebronics Pages: 6

Brand: Aroflora Pages: 36

Brand: Viking Pages: 5

WaterGuard CM2300

Brand: Mobeye Pages: 32

Brand: PROAIM Pages: 3

Brand: UBEXi Pages: 16

Brand: R&S Pages: 44

Brand: NuTone Pages: 6

Brand: Tripp Lite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands