Endress+Hauser Proline Promag 55 Operating Manual Download Page 93

Page: 93 / 130

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

Sys. -
T-DAT Save/Load

AUTO - OOS

Use this parameter to save the parameter settings/configuration of the

transmitter

in a transmitter DAT (T-DAT), or to load the parameter

settings from the T-DAT into the EEPROM (

manual

backup function).

Application examples:
• After commissioning, the actual measuring point parameters can be

saved to the
T-DAT as a backup.

• If the transmitter is replaced for some reason, the data from the T-DAT

can be loaded into the new transmitter (EEPROM).

Options:

CANCEL
SAVE (from EEPROM to T-DAT)
LOAD (from the T-DAT into EEPROM)

Factory setting:

CANCEL

Note!

• If the target device has an older software version, the message

"TRANSM. SW-DAT" is displayed during startup. Then only the SAVE
option is available.

• LOAD

This option is only possible if:
– The target device has the same software version as, or a more recent

software version than, the source device or

– The T-DAT contains valid data that can be retrieved

• SAVE

This option is always available.

"Diagnosis" Transducer Block/base index 1600

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands