Endress+Hauser Proline Promag 55 Operating Manual Download Page 80 | Manualshive

Page: 80 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

80

Hauser

System Unit -
Mass Flow

AUTO - OOS

Use this parameter to select the unit for the mass flow (mass/time).

The unit you select here is also valid for:
• Simulation
• Low flow cut off
• Display value (local display)

Options:

Metric:
gram

→

g/s; g/min; g/h; g/day

kilogram

→

kg/s; kg/min; kg/h; kg/day

Metric ton

→

t/s; t/min; t/h; t/day

US:
ounce

→

oz/s (US); oz/min (US); oz/h (US); oz/day (US)

pound

→

lb/s; lb/min; lb/h; lb/day

ton

→

ton/s; ton/min; ton/h; ton/day

Factory setting:

Nominal diameter and country dependent

!

Note!

The unit selected here does not have any effect on the desired mass flow
unit which should be transmitted by means of the FOUNDATION
Fieldbus interface. This setting is made separately by means of the
corresponding AI Block in the XD_SCALE parameter group.

System Value -
Fixed Density

read only

Use this function to view the set density.
This density value can be modified by means of the "Density Param. -
Fixed Value" parameter (

Factory setting:

1

!

Note!

The unit is displayed in the "System Unit - Fixed Density" parameter
(

System Unit -
Fixed Density

AUTO - OOS

Use this parameter to select the unit for displaying the fluid density.

The unit you select here is also valid for:
• Density entry "Density Param. - Fixed Value",

Options:

Metric

→

g/cm

3

; g/cc; kg/dm

3

; kg/l; kg/m

3

; SD 4 °C, SD 15 °C,

SD 20 °C; SG 4 °C, SG 15 °C, SG 20 °C; g/l

US

→

lb/ft

3

; lb/gal; lb/bbl (normal fluids); lb/bbl (beer); lb/bbl

(petrochemicals);
lb/bbl (filling tanks)

Imperial

→

lb/gal; lb/bbl (beer); lb/bbl (petrochemicals)

Factory setting:

kg/l (SI units: not for USA and Canada)
g/cc (US units: only for USA and Canada)

SD = Specific Density, SG = Specific Gravity
The specific density is the ratio of fluid density to water density
(at water temperature = 4, 15, 20 °C).

"Flow" Transducer Block/base index 1400

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
78
79
80
81
82
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Campbell Pages: 46

Brand: V-ZUG Pages: 12

Brand: Panasonic Pages: 16

Brand: NEC Pages: 8

Brand: X-pole Pages: 16

Brand: Danfoss Pages: 4

Brand: Valcom Pages: 1

Brand: Valcom Pages: 13

Brand: Valcom Pages: 3

Brand: Valcom Pages: 4

Brand: Yeti Pages: 19

Brand: veba Pages: 11

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands