Endress+Hauser Proline Promag 55 Operating Manual Download Page 23

Page: 23 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

5 Block USER INTERFACE

Hauser

5.1.3

Function group OPERATION

USER INTERFACE

⇒

CONTROL

CAA

⇒

BASIC CONFIGURATION 200

⇓

UNLOCKING/LOCKING 202

⇓

OPERATION

204

Function description

USER INTERFACE

→

CONTROL

→

OPERATION

TEST DISPLAY
(2040)

Use this function to test the operability of the local display and its pixels.

Options:

OFF
ON

Factory setting:

OFF

Test sequence:
1.

Start the test by selecting ON.

All pixels of the main line, additional line and information line are darkened for
minimum 0.75 seconds.

Main line, additional line and information line show an "8" in each field for minimum
0.75 seconds.

Main line, additional line and information line show a "0" in each field for minimum
0.75 seconds.

Main line, additional line and information line show nothing (blank display) for
minimum 0.75 seconds.

When the test completes the local display returns to its initial state and the setting
changes to OFF.

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands