Endress+Hauser Proline Promag 55 Operating Manual Download Page 13

Page: 13 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

3 Block MEASURED VARIABLES

Hauser

3.2.2

Function group ADDITIONAL CONFIGURATION

MEASURED

VARIABLES

⇒

MEASURING VALUES

AAA

⇓

SYSTEM UNITS

ACA

⇒

CONFIGURATION

040

⇓

ADDITIONAL CONF.

042

Function description

MEASURED VARIABLES

→

SYSTEM UNITS

→

ADDITIONAL CONFIGURATION

UNIT DENSITY
(0420)

Use this function to select the unit for displaying the fluid density.

The unit you select here is also valid for:
• Fluid density entry

Options:

Metric

→

g/cm

; g/cc; kg/dm

; kg/l; kg/m

; SD 4 °C, SD 15 °C, SD 20 °C; SG 4 °C,

SG 15 °C, SG 20 °C; g/l

→

lb/ft

; lb/gal; lb/bbl (normal fluids); lb/bbl (beer); lb/bbl (petrochemicals);

lb/bbl (filling tanks)

Imperial

→

lb/gal; lb/bbl (beer); lb/bbl (petrochemicals)

Factory setting:

kg/l (SI units: not for USA and Canada)
g/cc (US units: only for USA and Canada)

SD = Specific Density, SG = Specific Gravity
The specific density is the ratio of fluid density to water density
(at water temperature = 4, 15, 20 °C).

UNIT LENGTH
(0424)

Use this function to select the unit for displaying the length of the nominal diameter.

The unit you select here is also valid for:
Nominal diameter of sensor (function NOMINAL DIAMETER (6804) on Page 51)

Options:

MILLIMETER
INCH

Factory setting:

MILLIMETER (SI units: not for USA and Canada)
INCH (US units: only for USA and Canada)

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands