Endress+Hauser Proline Promag 55 Operating Manual Download Page 72 | Manualshive

Page: 72 / 130

background image

2 Resource Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

72

Hauser

2.3

Write protection and simulation

Write protection of the device parameters and simulation in the Analog Input and Discrete Output
function block can be locked or unlocked via a jumper setting on the FOUNDATION Fieldbus
I/O board (

→

Operating Instructions for Proline Promag 55 FOUNDATION Fieldbus, BA126D).

The parameter WRITE_LOCK shows the status of the hardware write protection. The following
statuses are possible:

The parameter BLOCK_ERR indicates whether a simulation is possible in the Analog Input and
Discrete Output function block.

2.4

Alarm detection and processing

Process alarms provide information on particular block statuses and block events. The status of the
process alarms is communicated to the fieldbus host system via the parameter BLOCK_ALM. The
parameter ACK_OPTION specifies whether an alarm must be acknowledged via the fieldbus host
system.

The following process alarms are generated by the Resource Block:

Block process alarms

The following block process alarms of the Resource Block are shown via the parameter
BLOCK_ALM:

Write protect process alarm

If write protection is disabled on the FOUNDATION Fieldbus I/O board, then prior to
communicating the change of status to the fieldbus host system the alarm priority specified in the
parameter WRITE_PRI is checked. The alarm priority specifies the action taken when the write
protection alarm WRITE_ALM is enabled.

!

Note!
• If the option of a process alarm has

not

been enabled in the parameter ACK_OPTION, this process

alarm only has to be acknowledged in the parameter BLOCK_ALM.

• The parameter ALARM_SUM shows the current status of all the process alarms.

– LOCKED

= Device data cannot be modified by means of the FOUNDATION

Fieldbus interface.

– NOT LOCKED

= Device data can be modified by means of the FOUNDATION

Fieldbus interface.

– Simulation Active

= Simulation possible in the Analog Input function block via the

SIMULATE parameter and in the Discrete Output function block via
the SIMULATE_D parameter.

– OUT OF SERVICE

– SIMULATE ACTVE

«
...
70
71
72
73
74
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: ULTIMATE SPEED Pages: 19

Brand: Galeo Pages: 19

Brand: Abicor Binzel Pages: 44

Brand: Yeti Pages: 19

Brand: veba Pages: 11

Brand: Honda Pages: 73

Brand: Bercomac Pages: 20

Brand: AOR Pages: 29

Brand: EVA Logik Pages: 2

Centronic VarioControl VC280

Brand: Becker Pages: 20

Brand: Acuity Brands Pages: 3

AAB-P-RZR900-K2-001

Brand: SuperATV Pages: 3

Brand: Omega Engineering Pages: 13

Brand: Gardena Pages: 13

Brand: Fisher-Price Pages: 12

Brand: Lambrecht Pages: 11

Brand: Peco Pages: 12

Brand: Valor Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands