Endress+Hauser Proline Promag 55 Operating Manual Download Page 108 | Manualshive

Page: 108 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

108

Hauser

3.6

Parameters of the "Totalizer" Transducer Block

The following table shows all the Hauser-specific parameters of the "Totalizer" Transducer
Block. These can only be changed after entering an enabling code in the "Access - Code"
parameter.

!

Note!
FOUNDATION Fieldbus parameters are described in the "FOUNDATION Fieldbus Overview"
Operating Instructions (BA013S) (available at:

→

www.endress.com

→

Download).

"Totalizer" Transducer Block/base index 1900:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

Access - Code

AUTO - OOS

All data of the measuring system are protected against inadvertent change.
Only when the code has been entered in this parameter can the
manufacturer-specific parameters be programmed and the device
configuration modified.

You can enable programming by entering:
• Code 55 (factory setting)
• Private code (

User input:

Max. 4-digit number (0 to 9999)

!

Note!

• If the write protection is enabled then access to the manufacturer-

specific parameters is blocked even if the right code is entered. Write
protection can be activated and deactivated by means of jumpers on the
I/O board (

→

see Operating Instructions for Proline Promag 55

FOUNDATION Fieldbus, BA126D).

• You can disable programming again by entering any number (other than

the access code) in this parameter.

• The Hauser service organization can be of assistance if you lose

your private code.

• Certain parameters are not accessible unless a special service code is

entered. This service code is known only to the Hauser service
organization. Please contact your Hauser service center if you
require clarification.

• The entry made here does not affect the local display. Thus,

programming via the function matrix must be enabled separately.

Access - Status

read only

Use this parameter to display the current status of the possibilities for
accessing the manufacturer-specific parameters of the device.

User interface:

• LOCKED (parameterization disabled)
• ACCESS CUSTOMER (parameterization enabled)
• ACCESS SERVICE (parameterization enabled, access to service level)

«
...
106
107
108
109
110
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Palm Pages: 14

Brand: Toco Pages: 12

Brand: Eaton Pages: 21

Brand: AC Schnitzer Pages: 16

Brand: Campbell Pages: 64

Brand: Campbell Pages: 42

Brand: Campbell Pages: 19

Brand: Campbell Pages: 26

Brand: Campbell Pages: 19

Brand: Campbell Pages: 27

Brand: Raven Pages: 24

Brand: Campbell Pages: 14

Brand: Campbell Pages: 2

TEMPERATURE PROBE 109SS

Brand: Campbell Pages: 18

Brand: Campbell Pages: 77

Brand: Campbell Pages: 30

Brand: Weather Guard Pages: 4

Brand: Campbell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands