Endress+Hauser Proline Promag 55 Operating Manual Download Page 22 | Manualshive

Page: 22 / 130

background image

5 Block USER INTERFACE

Device Functions Proline Promag 55 FOUNDATION Fieldbus

22

Hauser

5.1.2

Function group UNLOCKING/LOCKING

USER INTERFACE

C

⇒

CONTROL

CAA

⇒

BASIC CONFIGURATION 200

⇓

UNLOCKING/LOCKING 202

Function description

USER INTERFACE

→

CONTROL

→

UNLOCKING/LOCKING

ACCESS CODE
(2020)

!

Note!

This function is only relevant for local operation. If functions or parameters are to be
changed via the fieldbus, programming must be enabled separately via the parameter
"Access - code"/Transducer Blocks.

All data of the measuring system are protected against inadvertent change. Programming
is disabled and the settings cannot be changed until a code is entered in this function. If
you press the

X

key combination in any function, the measuring system automatically

goes to this function and the prompt to enter the code appears on the display (when
programming is disabled).

You can enable programming by entering your private code
(

factory setting = 55,

see DEFINE PRIVATE CODE function 2021).

User input:

Max. 4-digit number: 0 to 9999

!

Note!

• The programming levels are disabled if you do not press a key within 60 seconds

following automatic return to the HOME position.
You can also disable programming in this function by entering any number (other than
the defined private code).

• The Hauser service organization can be of assistance if you mislay your

private code.

DEFINE PRIVATE CODE
(2021)

Use this function to specify a private code for enabling programming in the function
ACCESS CODE (2020).

User input:

0 to 9999 (max. 4-digit number)

Factory setting:

55

!

Note!

• Programming is always enabled with the code "0".
• Programming has to be enabled before this code can be changed. When programming

is disabled this function is not available, thus preventing others from accessing your
private code.

STATUS ACCESS
(2022)

Use this function to check the access status for the function matrix.

User interface:

ACCESS CUSTOMER (parameterization possible)
LOCKED (parameterization disabled)

ACCESS CODE
COUNTER
(2023)

Displays how often the customer code, service code or the digit "0" (code-free) has been
entered to gain access to the function matrix.

User interface:

Max. 7-digit number: 0 to 9999999

Factory setting:

0

«
...
20
21
22
23
24
...
»

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Brand: Calumet Pages: 4

Brand: Samsung Pages: 7

Brand: Xplova Pages: 13

projectorsleeve

Brand: 3M Pages: 14

Brand: 3LeggedThing Pages: 9

Brand: Bachmann Pages: 2

Brand: Oki Pages: 2

Brand: OKIDATA Pages: 16

Brand: Valor Pages: 6

Brand: Valor Pages: 6

Portrait Series

Brand: Valor Pages: 6

Brand: Valor Pages: 10

Brand: Zhiyun Pages: 10

Brand: Fantec Pages: 5

Brand: Camcar Pages: 2

Brand: Omron Pages: 8

Brand: ACERBIS Pages: 72

Brand: Fullwat Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands