Endress+Hauser Proline Promag 55 Operating Manual Download Page 42

Page: 42 / 130

7 Block BASIC FUNCTION

Device Functions Proline Promag 55 FOUNDATION Fieldbus

Hauser

7.1.2

Function group FUNCTION BLOCKS

BASIC FUNCTION

⇒

FOUNDATION FIELDBUS GGA

⇒

CONFIGURATION

620

⇓

FUNCTION BLOCKS

622

Function description

BASIC FUNCTION

→

FOUNDATION FIELDBUS

→

FUNCTION BLOCKS

BLOCK SELECTION
(6220)

Use this function to select a function block whose value and status is shown in the
subsequent functions.

Options:

ANALOG INPUT 1
ANALOG INPUT 2
ANALOG INPUT 3
ANALOG INPUT 4
ANALOG INPUT 5
PID

Factory setting:

ANALOG INPUT 1

OUT VALUE
(6221)

Use this function to display the output value OUT, incl. unit and status, of the Analog
Input or PID function block selected in the BLOCK SELECTION function (6220).

PID_IN VALUE
(6222)

Note!

This function is not available unless the PID selection was selected in the
BLOCK SELECTION (6220) function.

User interface:

Use this function to display the controlled variable IN, incl. unit and status, of the PID
function block.

CASCADE_IN
(6223)

Note!

This function is not available unless the PID selection was selected in the
BLOCK SELECTION (6220) function.

User interface:

Display of an analog set value, incl. units and status, taken over from an external function
block.

SETPOINT VALUE
(6224)

Note!

• This function is not available unless the PID selection was selected in the

BLOCK SELECTION (6220) function.

• If the service code is used to call this function, this value can be edited.

User interface:

Use this function to display the internal set value, incl. unit and status, for the PID
function block.

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands