manualshive.com logo in svg

Endress+Hauser Proline Promag 55, Operating Manual

The Endress+Hauser Proline Promag 55 is a cutting-edge flow meter designed for accurate measurements in various industrial applications. Enhance your understanding and optimize performance with the comprehensive Operating Instructions Manual available for free download at manualshive.com, ensuring you have access to all the necessary information to successfully operate this exceptional product.

Share
Download
background image

Device functions Proline Promag 55 FOUNDATION Fieldbus

3 Transducer Block

Hauser

77

The CHANNEL parameter in the Analog Input function block is used to assign which process 
variable is read in and processed in the downstream Analog Input function block:

• Process variable Calculated Mass Flow 

→

 CHANNEL 1 (Analog Input function block)

• Process variable Volume Flow

→

 CHANNEL 2 (Analog Input function block)

• Process variable Totalizer 1 

→

 CHANNEL 7 (Analog Input function block)

• Process variable Totalizer 2 

→

 CHANNEL 8 (Analog Input function block)

• Process variable Totalizer 3 

→

 CHANNEL 9 (Analog Input function block)

3.2.2

Selecting the operating mode

The operation mode is set by means of the MODE_BLK parameter group. The Transducer Blocks 
support the following operation modes:

• AUTO (automatic mode)
• OOS (out of service)

!

Note!
• The block status OOS is also shown via the parameter BLOCK_ERR. In operating mode OOS, if 

write protection is not enabled and the access code is entered, you can access all the write 
parameters without restriction.

• The following applies for the "Flow" and "Totalizer" Transducer Blocks: With the "OOS" operating 

mode, the process variables are updated but the status of the output value OUT (AI Block) changes 
to "BAD".

• If problems occur during the configuration of the function blocks 

→

 see Operating Instructions 

for  Proline Promag 55 FOUNDATION Fieldbus (BA126D), "Troubleshooting" section. 

3.2.3

Alarm detection and processing

The Transducer Blocks do not generate any process alarms. The status of the process variables is 
evaluated in the downstream Analog Input function blocks. If the Analog Input function block does 
not receive an input value that can be evaluated from the "Flow" or "Totalizer" Transducer Blocks, 
then a process alarm is generated. This process alarm is displayed in the BLOCK_ERR parameter of 
the Analog Input function block (BLOCK_ERR = Input Failure).

The parameter BLOCK_ERR of the Transducer Blocks displays the device error that produced the 
input value that could not be evaluated and thus triggered the process alarm in the Analog Input 
function block.

In addition, the active device error is displayed via the "Diagnosis" Transducer Block in the 
"Diagnosis - Act.Sys. Condition" parameter (

  →  

Page 90). 

For further information on rectifying errors 

→ 

see

 

 Operating Instructions for Proline Promag 55 

FOUNDATION Fieldbus (BA126D), "Troubleshooting" section.

3.2.4

Diagnosis

The status of the device is displayed via the following parameters specified in the FOUNDATION 
Fieldbus specification:

• BLOCK_ERR 
• Transducer Error 

More detailed information on the current device status is displayed via the "Diagnosis" Transducer 
Block in the manufacturer-specific parameter "Diag. - Act.Sys.Condition" (

  →  

Page 90).

For further information on rectifying errors 

→

see Operating Instructions for Proline Promag 55 

FOUNDATION Fieldbus (BA126D), "Troubleshooting" section.

Summary of Contents for Proline Promag 55



































































































































Reviews:

No comments

Related manuals for Proline Promag 55

Manfrotto 357 Instructions preview
357
Brand: Manfrotto Pages: 2
Salta 5365 User Manual preview
5365
Brand: Salta Pages: 76
Saft 2506 Overhaul Manual preview
2506
Brand: Saft Pages: 52
Obelink LIVING Pitching Instruction preview
LIVING
Brand: Obelink Pages: 2
Leuze SET-AC Manual preview
SET-AC
Brand: Leuze Pages: 9
UNINEX KOOLZONE SAC-1800 Quick User Manual preview
KOOLZONE SAC-1800
Brand: UNINEX Pages: 5
Groov-e GV-WM4 Fitting Instructions preview
GV-WM4
Brand: Groov-e Pages: 2
TrailFX A4012S Installation Instructions Manual preview
A4012S
Brand: TrailFX Pages: 6
Chariot Carriers 51100913 Instruction Manual preview
51100913
Brand: Chariot Carriers Pages: 3
Trail-Gator 640025 Owner'S Manual preview
640025
Brand: Trail-Gator Pages: 44
Omni Ultraviolet UV WAND SANITIZER Manual preview
UV WAND SANITIZER
Brand: Omni Ultraviolet Pages: 5
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Brand: KRAFTWERK Pages: 2
X-Moove Powereco 10 000 User Manual preview
Powereco 10 000
Brand: X-Moove Pages: 3
INNOBIZ BULIA Instructions For Use Manual preview
BULIA
Brand: INNOBIZ Pages: 88
QualGear PRB-717-WHT Installation Manual preview
PRB-717-WHT
Brand: QualGear Pages: 6
AC Schnitzer DKG Fitting Instructions Manual preview
DKG
Brand: AC Schnitzer Pages: 16
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Brand: Hella Pages: 21
KAMA MESTIC MCC-25 Instruction Manual preview
MESTIC MCC-25
Brand: KAMA Pages: 20

Brands by name

Popular brands

Load more brands