Endress+Hauser Proline Promag 55 Operating Manual Download Page 37

Page: 37 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

6 Block TOTALIZER

Hauser

TOTALIZER MODE
(3002)

Use this function to define how the flow components are to be totalized.

Options:

BALANCE
Positive and negative flow components. The positive and negative flow components are
balanced. In other words, net flow in the flow direction is registered.

FORWARD
Positive flow components only

REVERSE
Negative flow components only

Factory setting:

Totalizer 1 = BALANCE
Totalizer 2 = FORWARD
Totalizer 3 = REVERSE

RESET TOTALIZER
(3003)

Use this function to reset the sum and the overflow of the totalizer to zero.

Options:

NO
YES

Factory setting:

Function description

TOTALIZER

→

TOTALIZER (1 to 3)

→

CONFIGURATION

Summary of Contents for Proline Promag 55



































































































































Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands

Endress+Hauser Proline Promag 55, Operating Manual

Search results

Summary of Contents for Proline Promag 55

Reviews:

Related manuals for Proline Promag 55

Brands by name

Popular brands