Chapter 14 Fault Codes | IED-S
14-11
Code#
KPC-CC01 Display
Fault Name
Description
F152
Runs with door open
Detection is valid only when not in the manual mode or
not in door unlock board test mode. There are two
detection conditions:
1. Fault occurs when both the gate safety hatch and
layer door safety hatch signals are OFF, and the
door zone signal changes from ON to OFF.
2. Both the gate safety hatch and layer door safety
hatch signals use their own relays to connect
multi-function terminals (MI=20 GSNC (N.C contact
of gate safety hatch contactor)) and MI=23 DSNC
(N.C. contact of layer door safety hatch contactor)).
Fault occurs when their signals are both OFF and
they are not in the manual mode for more than 30
seconds and not in the door zone.
Action and Reset
Action
Stops urgently
Related Parameters
Pr.03-59 (Door Unlock Board Test)
Reset Method
Press the external reset device, press the RESET key on the digital keypad,
power-on again, or switch to the inspection mode to press both the upward and
downward operation buttons simultaneously for more than five seconds (choose
either)
Code#
KPC-CC01 Display
Fault Name
Description
F153
Safety hatch low
voltage error
Fault occurs when there is an error in the safety hatch
signal for the elevator system (low voltage)
Action and Reset
Action
Stops urgently
Related Parameters
MI=16 SFL (Safety hatch low voltage)
Reset Method
Resets automatically once the signal is normal
Code#
KPC-CC01 Display
Fault Name
Description
F154
Runs in an opposite
direction
Fault occurs when the elevator running direction is
opposite to the encoder direction.
Action and Reset
Action
Three seconds
Related Parameters
Pr.03-22 (Reverse Pulse Logic) or Pr.13-02 (Drive Output Direction)
Reset Method
When the elevator is in stop status, press the RESET key on the digital keypad,
press the external reset device, or power-on again (choose either)
Code#
KPC-CC01 Display
Fault Name
Description
F155
BK3 is not active
Fault occurs when BK3 (Brake-3 travel switch) signal is
not active after brake contactor activates (ON)
Action and Reset
Action
Stops urgently
Related Parameters
MI=32 BK3 (Brake-3 travel switch)
Reset Method
Press the upward or downward operation button for the manual mode, press the
RESET key on the digital keypad, press the external reset device, or power-on
again (choose either)
Summary of Contents for IED-S Series
