Chapter 12 Descriptions of Parameter Settings | IED-S
12-06-7
Setting
Value
MI Function
Description
ON; under automatic mode when LED indicator is
OFF. Car inspection mode has the lowest priority for
inspection mode (lower than emergency operation).
154
IICUP (Car inspection upward and
attendant direction change)
When LED indicator is ON:
Executes inspection upward operation while in car
inspection mode.
Forces to change the elevator running direction
while in attendant mode.
155
IICDN (Car inspection downward and
attendant direct landing)
When LED indicator is ON:
Executes inspection downward operation while in
car inspection mode.
Makes elevator stop at registered car call only, and
does not respond to hall call. But hall call remains
registered and cannot be cancelled while in
attendant mode.
156
CARD (Car reader)
Car call can be registered only when LED indicator
is ON.
157
CFNLT (Car fan and lighting control
switch)
Fan stops and lighting is off when LED indicator is
ON.
158
ESS (Stop at each floor)
Executes stop at each floor for car call when LED
indicator is ON. For example, if the elevator stops at
1F, and there is a car call from 5F, it will stop at each
floor–2F, 3F, and 4F–before arriving at 5F.
159
FUP (Manual upward fine-tune button)
When LED indicator is ON and door open extended
button is activated, elevator is forced to run upward
manually at fine-tuned speed under automatic
mode, and runs with Pr.04-05 (Leveling Speed)..
160
FDN (Manual downward fine-tune
button)
When LED indicator is ON and door open extended
button is activated, elevator is forced to run
downward manually at fine-tuned speed under
automatic mode, and runs with Pr.04-05 (Leveling
Speed).
161
ISS (Independent operation switch)
The elevator runs in normal mode independently
instead of parallel control when LED indicator is ON.
162
IND (Goods only switch)
Enters goods carrying mode when LED indicator is
ON.
163
ATS (Attendant mode)
An attendant is accompanied in the elevator to
control upward or downward running and make
elevator stop at designated floor as per passenger
needs.
164
VIP (VIP mode)
165
CLIS (Car lighting switch)
Car lighting equipment is off when LED indicator is
ON.
166
FS (Car fan switch)
Car fan stops when LED indicator is ON.
167
DCB2 (Rear door close button)
Rear door close button is pressed when LED
indicator is ON.
168
DOB2 (Rear door open button)
Rear door open button is pressed when LED
indicator is ON.
169
DOBH2 (Rear door open extended
button)
Rear door open extended button is pressed when
LED indicator is ON.
170
DCB1B (Front door close auxiliary
button)
Front door close auxiliary button is pressed when
LED indicator is ON.
171
DOB1B (Front door open auxiliary
button)
Front door open auxiliary button is pressed when
LED indicator is ON.
172
DOBH1B (Front door open auxiliary
extended button)
Front door open auxiliary extended button is
pressed when LED indicator is ON.
173
DCB2B (Rear door close auxiliary
button)
Rear door close auxiliary button is press when LED
indicator is ON.
174
DOB2B (Rear door open auxiliary
Rear door open auxiliary button is pressed when
Summary of Contents for IED-S Series
