Dell D630 - LATITUDE ATG NOTEBOOK User Manual Download Page 87

Page: 87 / 218

Securing Your Computer

Slide the smart card into the smart card slot until the card is completely

seated in its connector. The smart card will protrude approximately 1/2

inch from the slot. The smart card slot is located below the PC Card slot.
If you encounter too much resistance, do not force the card. Check the

card orientation and try again.

Passwords

Passwords prevent unauthorized access to your computer. When using

passwords, observe the following guidelines:

• Choose a password that you can remember, but not one that is easy to

guess. For example, do not use the names of family members or pets for

passwords.

• It is recommended that you do not write down your password. If you do

write it down, however, ensure that the password is stored in a secure place.

• Do not share your password with other people.
• Ensure that people are not watching you when you type your password.

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK



























































































































































































































Search results

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK

Reviews:

Brands by name

Popular brands

Dell D630 - LATITUDE ATG NOTEBOOK, User Manual

Search results

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK

Reviews:

Brands by name

Popular brands