manualshive.com logo in svg

Dell D630 - LATITUDE ATG NOTEBOOK, User Manual

Share
Download
Dell D630 - LATITUDE ATG NOTEBOOK User Manual Download Page 121

Troubleshooting

121

C

H E C K

 

T H E

 

S TA T U S

 

I N

 

T H E

 D

E L L

 M

O B I L E

 B

R O A D B A N D

 C

A RD

 U

T I L I T Y

—

Click 

the 

icon on the Windows desktop to launch the utility. Check the status in 

the main window:

•

No card detected

 – Restart the computer and launch the utility 

again. 

•

Radio Off

 – Ensure the Mobile Broadband card is enabled by viewing 

the status in the Dell Mobile Broadband Card Utility. If the card is 

disabled, enable the Mobile Broadband card by clicking the 

Turn Radio 

On

 button in the main screen of the Dell Mobile Broadband Card Utility.

•

Searching

 – The Dell Mobile Broadband Card Utility has not yet 

located a Mobile Broadband network. If the searching state persists, ensure 

that the signal strength is adequate.

•

No service

 – The Dell Mobile Broadband Card Utility did not locate a 

Mobile Broadband network. Ensure that the signal strength is adequate. 

Restart the Dell wireless utility or contact your Mobile Broadband network 

provider.

•

Check your Mobile Broadband Network Service

 – Contact 

your Mobile Broadband network service provider to verify coverage plan 

and supported services.

A

C T I V A T E

 

Y O U R

 M

O B I L E

 B

R O A D B A N D

 

CAR D

—

Before you connect to the 

Internet, you must activate the Mobile Broadband service through your cellular 

service provider. For instructions and for additional information about using the 

Dell Mobile Broadband Card Utility, see the user's guide available through the 

Windows Help and Support Center (click 

Start

→

 

Help and Support

). The 

user's guide is also available on the Dell Support website at 

support.dell.com

 

and on the media included with your Mobile Broadband card if you purchased 

the card separately from your computer.

PC Card Problems

Fill out the Diagnostics Checklist (see "Diagnostics Checklist" on page 198) as 

you complete these checks.

 

CAUTION: 

Before you begin any of the procedures in this section, follow the 

safety instructions in the 

Product Information Guide

.

C

H E C K

 

T H E

 C

A R D

—

Ensure that the card is properly inserted into the 

connector.

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK



























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands