Dell D630 - LATITUDE ATG NOTEBOOK User Manual Download Page 186

Page: 186 / 218

186

Specifications

Video

NOTE:

Your Dell™ Latitude™ D630 computer has both integrated and discrete video

options.

Video type:

integrated and discrete on system board,

hardware accelerated

Data bus

integrated video or PCI-E graphics x16

Video controller

Intel GMA X3100 or

NVIDIA Quadro NVS 135M

Video memory

integrated video up to 128 MB, discrete

128 -MB dedicated memory, up to 256 MB

shared (additional NVIDIA Turbo Cache

available)

Audio

Audio type

two-channel high definition audio (Azalia)

Audio controller

IDT STAC9205 Codec

Stereo conversion

24-bit (analog-to-digital and digital-to-

analog)

Interfaces:

Internal

high definition audio (Azalia) codec

External

microphone-in connector, stereo

headphones/speakers connector

Speaker

one 4-ohm speaker

Internal speaker amplifier

2-W channel into 4 ohms

Volume controls

volume control buttons, program menus

Display

Type (active-matrix TFT)

WXGA or WXGA+

Active area (X/Y)

303.74 x 189.84

Dimensions:

Height

206 mm (8.11 inches)

Width

320 mm (12.6 inches)

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK



























































































































































































































Search results

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK

Reviews:

Brands by name

Popular brands

Dell D630 - LATITUDE ATG NOTEBOOK, User Manual

Search results

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK

Reviews:

Brands by name

Popular brands