manualshive.com logo in svg

Dell D630 - LATITUDE ATG NOTEBOOK, User Manual

Share
Download
Dell D630 - LATITUDE ATG NOTEBOOK User Manual Download Page 157

Adding and Replacing Parts

157

4

Remove the battery connector from the connector on the system board.

5

Being careful not to break the plastic, slightly raise the corner of the mylar 

above the battery.

6

While holding the mylar, grasp the battery and pull out of the battery 

compartment.

Memory

You can increase your computer memory by installing memory modules on the 

system board. See "Specifications" on page 183 for information on the memory 

supported by your computer. Install only memory modules that are intended for 

your computer.

 

CAUTION: 

Before you begin any of the procedures in this section, follow the 

safety instructions in the 

Product Information Guide

.

 

NOTICE: 

If your computer has only one memory module, install the memory module 

in the connector labeled “DIMMA.” 

1

battery connector

2

coin-cell battery

3

mylar

2

1

3

Summary of Contents for D630 - LATITUDE ATG NOTEBOOK



























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands