Dell Command Line Interface User Manual Download Page 64

Page: 64 / 226

omconfig: Managing Components Using the Instrumentation Service

config=serial baudrate=9600 | 19200 | 38400 |57600

| 115200

9600:

Sets connection speed to 9600 bits per

second.

19200

:Sets connection speed to 19200 bits per

second.

38400

: Sets connection speed to 38400 bits per

second.

57600

: Sets connection speed to 57600 bits per

second.

115200

: Sets connection speed to 115200 bits

per second.

NOTE:

Baud rates of 9600, 19200, 38400, and

57600 are supported on PowerEdge 1800,1850,
2800, and 2850 systems.
Baud rates of 9600, 19200, and 57600 are
supported on PowerEdge

systems.

Baud rate of 115200 is supported on certain
systems that have a DRAC 5 installed.

flowcontrol=none | rtscts

none

: No control over the flow of

communication through the serial port.

rtscts

: RTS is ready to send and CTS is clear to

send.

Table 4-3.

omconfig chassis bmc

(continued)

name=value pair 1
config=

name=value pair 2

Description

Summary of Contents for Command Line Interface



































































































































































































































Search results

Summary of Contents for Command Line Interface

Reviews:

Related manuals for Command Line Interface

Brands by name

Popular brands

Dell Command Line Interface, User Manual

Search results

Summary of Contents for Command Line Interface

Reviews:

Related manuals for Command Line Interface

Brands by name

Popular brands