manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

omreport: Viewing System Status Using the Instrumentation Service

29

omreport chassis bmc

 

NOTE: 

This command will be phased-out in future releases. It will be replaced by the command 

omreport chassis 

remoteaccess

.

Use the 

omreport chassis bmc

 command to view baseboard management controller (BMC) 

general information.

Type:

omreport chassis bmc

The output from the 

omreport chassis bmc

 command lists each of the valid parameters. Table 3-3 shows 

the available settings.

RAID Channel A

Displays whether RAID-on-motherboard Channel A is detected as a 
RAID device or a SCSI device.

RAID Channel B

Displays whether RAID-on-motherboard Channel B is detected as a 
RAID device or a SCSI device.

SATA

Displays whether the onboard SATA controller is set to ATA mode, 
RAID mode, or is disabled.

SATA port

Displays if the SATA port is enabled or disabled.

Secondary SCSI

Displays whether the device is enabled or disabled.

Serial Communications

Displays whether COM port 1 and COM port 2 are enabled or 
disabled with or without console redirection.

Serial Port 1

Displays whether serial port 1 is mapped to a COM port, a 
COM port 1, a COM port 3, a COM1 BMC, a BMC Serial, a BMC 
NIC, a BMC RAC, or is disabled.

Serial Port 2

Displays whether serial port 2 is mapped to a COM port, a 
COM port 2, a COM port 4, or is disabled.

Speaker

Displays whether the speaker is on or off.

USB or USBB

Displays whether the USB port is enabled or disabled.

User accessible USB

Displays whether the user-accessible USB port is enabled or disabled.

Table 3-2.

BIOS Setup Parameters 

(continued)

Parameters

Description

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
NavigateWorx NR300 User Manual preview
NR300
Brand: NavigateWorx Pages: 71
Grasslin TOWERCHRON DP72 Programming Manual preview
TOWERCHRON DP72
Brand: Grasslin Pages: 2
process-informatik CONNECT Series Operation Quick Start Manual preview
CONNECT Series
Brand: process-informatik Pages: 8
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
ZyXEL Communications XS1920 Series User Manual preview
XS1920 Series
Brand: ZyXEL Communications Pages: 422
TDK InvenSense RoboKit1 Hardware Reference Manual preview
InvenSense RoboKit1
Brand: TDK Pages: 13
Solwise WLn-401 Quick Installation Manual preview
WLn-401
Brand: Solwise Pages: 7
General DataComm PacketMate 1000 User Manual preview
PacketMate 1000
Brand: General DataComm Pages: 20
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
Weidmuller IE-SW-VL09T-6TX-3SC Hardware Installation Manual preview
IE-SW-VL09T-6TX-3SC
Brand: Weidmuller Pages: 14
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Brand: Corsair Pages: 11
METREL A 1475 Instruction Manual preview
A 1475
Brand: METREL Pages: 21
Billion BIPAC 7100G Quick Start Manual preview
BIPAC 7100G
Brand: Billion Pages: 14
Paradyne Application Module 9109 OCU-DP Installation Instructions Manual preview
Application Module 9109 OCU-DP
Brand: Paradyne Pages: 8
FiberHome AN5506-04 Series Product Manual preview
AN5506-04 Series
Brand: FiberHome Pages: 146
Arista CloudVision DCA-CV-100 Quick Start Manual preview
CloudVision DCA-CV-100
Brand: Arista Pages: 46
Cisco 861W - Integrated Services Router Wireless Quick Start Manual preview
861W - Integrated Services Router Wireless
Brand: Cisco Pages: 34

Brands by name

Popular brands

Load more brands