manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

152

Using the Storage Management Service

PDISKID=<connector:enclosureID:portID | connector:targetID> 

Use this parameter to specify the physical disks that will be included in the virtual disk. 

When reconfiguring a virtual disk, you must specify all physical disks to be included in the reconfigured 
virtual disk. The physical disk specification applies to physical disks that were in the original virtual disk 
and will continue to be in the reconfigured virtual disk and to any new physical disks being added to the 
reconfigured virtual disk. Some controllers allow you to remove a physical disk from a virtual disk. In this 
case, you would not specify the physical disk to be removed. 

The

 pdisk=<PDISKID>

 parameter indicates a physical disk by specifying either 

connector:enclosureID:portID or connector:targetID

. 

stripesize=< 2kb| 4kb| 8kb| 16kb| 32kb| 64kb| 128kb>] Parameter 

(Optional) 

Different controllers support different stripe sizes. See the online help for information on which stripe 
sizes are supported for a controller. All stripe sizes are specified in kilobytes. For example, when 
specifying 128 KB as the stripe size, enter: 

stripesize=128kb

[cachepolicy=<d | c>] Parameter (Optional) 

Different controllers support different cache policies. See the online help for more information. 
The following table indicates how to specify the

 [cachepolicy=<d | c>] 

parameter for each of the 

cache policies. 

[readpolicy=<ra| nra| ara| rc| nrc>] Parameter (Optional) 

Different controllers support different read policies. See the online help for more information. 
The following table indicates how to specify the 

[readpolicy=<ra| nra| ara| rc| nrc>] 

parameter for 

each of the read policies. 

Table 8-19.

Cache Policy Parameters

Cache Policy

cachepolicy=d | c Parameter Specification 

Direct I/O

cachepolicy=d

Cache I/O

cachepolicy=c

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
3Com 3C410012A - OfficeConnect Remote 531 Access... Getting Started Manual preview
3C410012A - OfficeConnect Remote 531 Access...
Brand: 3Com Pages: 72
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Brand: ICT Pages: 34
Planet ADSL 2/2+ VPN Firewall Router ADE-4300A/B User Manual preview
ADSL 2/2+ VPN Firewall Router ADE-4300A/B
Brand: Planet Pages: 132
H3C CR1606-F Installation Instructions Manual preview
CR1606-F
Brand: H3C Pages: 12
Maipu MP2900-04-AC Installation Manual preview
MP2900-04-AC
Brand: Maipu Pages: 80
Patton electronics Model 2711 User Manual preview
Model 2711
Brand: Patton electronics Pages: 13
Angel Cool Aironet 1200 Quick Start Manual preview
Aironet 1200
Brand: Angel Cool Pages: 2
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
WolfPack 18x18 Card Cage User Manual preview
18x18 Card Cage
Brand: WolfPack Pages: 31
ZyXEL Communications P-335U Specifications preview
P-335U
Brand: ZyXEL Communications Pages: 2
Amphenol C2LINX Series Installation Manual preview
C2LINX Series
Brand: Amphenol Pages: 43
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7
NetComm RTA100 User Manual preview
RTA100
Brand: NetComm Pages: 75
Proscend 6200-2W User Manual preview
6200-2W
Brand: Proscend Pages: 93
RouterBOARD OmniTik UPA-5HnD Quick Setup Manual And Warranty Information preview
OmniTik UPA-5HnD
Brand: RouterBOARD Pages: 4
National Instruments NI 653x User Manual preview
NI 653x
Brand: National Instruments Pages: 147
COMBA TB-1800 Equipment Manual preview
TB-1800
Brand: COMBA Pages: 57

Brands by name

Popular brands

Load more brands