manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

omconfig: Managing Components Using the Instrumentation Service

61

omconfig chassis bmc

 

NOTE: 

This command will be phased-out in future releases. It will be replaced by the command 

omconfig chassis 

remoteaccess

.

Use the 

omconfig chassis bmc

 command to configure:

•

The BMC on a local area network (LAN)

•

The serial port for BMC

•

The BMC on a serial over LAN connection

•

Terminal settings for the serial port

•

Advanced settings for a serial over LAN connection

•

Information on a BMC user

 

NOTE: 

You have to enter the user ID to configure user information.

Type:

omconfig chassis bmc

attribute=usb

setting=enabled | disabled

enabled

: Enables the USB port(s). 

disabled

: Disables the USB port(s).

NOTE: 

Depending on your system’s hardware, only 

one of the two attributes 

usb

 and 

usbb

 is available 

for configuring the USB port(s).

attribute=usbb

setting=enabled | 
enabledwithbios| disabled

enabled

: Enables the USB port(s) during system 

boot, without BIOS support. 

enabledwithbios:

 Enables the USB port(s) during 

the system boot, with BIOS support.

disabled

: Disables the USB port(s) during system 

boot.

NOTE: 

Depending on your system’s hardware, only 

one of the two attributes 

usb

 and 

usbb

 is available 

for configuring the USB port(s).

Table 4-2.

BIOS Setup 

(continued)

name=value pair 1
attribute=

name=value pair 2
setting=

Description

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
ICP DAS USA MSM-508 Quick Start preview
MSM-508
Brand: ICP DAS USA Pages: 4
JB Systems Scene Master Operation Manual preview
Scene Master
Brand: JB Systems Pages: 24
JB Systems CMX 24 User Manual preview
CMX 24
Brand: JB Systems Pages: 61
N-Tron 702-W User Manual & Installation Manual preview
702-W
Brand: N-Tron Pages: 62
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
PaloAlto Networks ION 1200 Series Hardware Reference Manual preview
ION 1200 Series
Brand: PaloAlto Networks Pages: 90
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
ZyXEL Communications VMG5313-BXB SERIES Quick Start Manual preview
VMG5313-BXB SERIES
Brand: ZyXEL Communications Pages: 2
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
Patton IPLink 2603 Series User Manual preview
IPLink 2603 Series
Brand: Patton Pages: 120
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
SriHome NVS001B Quick Operation Manual preview
NVS001B
Brand: SriHome Pages: 12
Airlink101 AR725W User Manual preview
AR725W
Brand: Airlink101 Pages: 64
ETAS ES1337.2 User Manual preview
ES1337.2
Brand: ETAS Pages: 29

Brands by name

Popular brands

Load more brands