Dell Command Line Interface User Manual Download Page 38

Page: 38 / 226

omreport: Viewing System Status Using the Instrumentation Service

omreport chassis slots

Use the

omreport chassis slots

command to view properties of your system’s slots.

Type:

omreport chassis slots index=

The

index

parameter is optional. If you do not specify the index, Server Administrator displays

properties for all of the slots in your system. If you specify the index, Server Administrator displays
properties for a specific slot.

For each slot in the system, values display for the following fields:

Index

Slot ID

Adapter

, and

Data Bus Width

Index

is the number of the slot in the system.

Slot ID

is the silk screen name printed on your system's motherboard next to the slot. Alphanumeric text

uniquely identifies each slot in the system.

Adapter

refers to the name and or type of the card that fits into the slot, for example, a storage array

controller, SCSI adapter, or HBA.

Data bus width

is the width, in bits, of the information pathway between the components of a system.

Data bus width range is 16 to 64 bits.

omreport chassis temps

Use the

omreport chassis temps

command to view properties of your system’s temperature probes.

When you type:

omreport chassis temps index=

The

index

parameter is optional. If you do not specify the index, Server Administrator displays a

summary of status, readings, and thresholds set for any temperature probes that might be present on
your system. If you specify the index, Server Administrator displays a summary for a specific
temperature probe.

Table 3-5.

omreport chassis remoteaccess

name=value pair

Description

config=advsol

Reports advanced BMC or RAC information on a serial over local area
network (LAN) connection.

config=nic

Reports BMC or RAC information for the LAN.

config=serial

Reports serial port information for BMC or RAC.

config=serialoverlan

Reports BMC or RAC information on a serial over LAN connection.

config=terminalmode

Reports terminal mode settings for the serial port.

config=user

Reports information on BMC or RAC users.

Summary of Contents for Command Line Interface



































































































































































































































Search results

Summary of Contents for Command Line Interface

Reviews:

Related manuals for Command Line Interface

Brands by name

Popular brands

Dell Command Line Interface, User Manual

Search results

Summary of Contents for Command Line Interface

Reviews:

Related manuals for Command Line Interface

Brands by name

Popular brands