manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

omreport: Viewing System Status Using the Instrumentation Service

27

Server Administrator reports values for the 

Redundancy Status

 and 

Redundancy Mode

 fields.

omreport chassis batteries

Use the 

omreport chassis batteries

 command to view battery properties.

omreport chassis bios

Use the 

omreport chassis bios 

command to view current BIOS information. When you type:

omreport chassis bios

Server Administrator displays a summary of your system’s BIOS information.

omreport chassis biossetup

Use the 

omreport chassis biossetup

 command to view BIOS setup parameters that are normally available 

only during system boot. 

Type:

omreport chassis biossetup

Table 3-2 displays the BIOS setup parameters that are available:

 

NOTE: 

Not all the parameters are displayed. Only those BIOS setup properties that are configured during system 

boot are displayed.

AC Power Lines

Status

:

Ok

Location

:

AC Power Line 1

AC Present

:

Power Present

Active Source

:

Active

Status

:

Ok

Location

:

AC Power Line 2

AC Present

:

Power Present

Active Source

:

Not Active

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
Juniper MX2010 Hardware Manual preview
MX2010
Brand: Juniper Pages: 825
Allied Telesis AT-8550/SP Series Installation Manual preview
AT-8550/SP Series
Brand: Allied Telesis Pages: 114
Belkin AC 1600 DB User Manual preview
AC 1600 DB
Brand: Belkin Pages: 57
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
Ubiquiti EdgeRouter 12 Quick Start Manual preview
EdgeRouter 12
Brand: Ubiquiti Pages: 23
Calix GS2020E GigaSPIRE BLAST Quick Start Manual preview
GS2020E GigaSPIRE BLAST
Brand: Calix Pages: 15
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Brand: Lindy Pages: 3
Atlantis Land Edge-Core A07-ES4548C Specification Sheet preview
Edge-Core A07-ES4548C
Brand: Atlantis Land Pages: 2
e+p OCH 110 Installation Manual preview
OCH 110
Brand: e+p Pages: 2
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Brand: 8e6 Technologies Pages: 76
Lanpro LP-SW811 User Manual preview
LP-SW811
Brand: Lanpro Pages: 6
Gigabyte GN-WIKG User Manual preview
GN-WIKG
Brand: Gigabyte Pages: 10
National Instruments PXI-7811 User Manual preview
PXI-7811
Brand: National Instruments Pages: 72
LOBENN LB200186 Installation Manual preview
LB200186
Brand: LOBENN Pages: 86

Brands by name

Popular brands

Load more brands