manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

omreport: Viewing System Status Using the Instrumentation Service

41

•

power supply warning

•

power supply failure

•

degraded redundancy

•

lost redundancy

•

temperature warning

•

temperature failure

•

voltage warning

•

voltage failure

•

processor warning

•

processor failure

•

hardware log warning

•

hardware log full

•

watchdog ASR

omreport system assetinfo

Use the 

omreport system assetinfo

 command to see cost of ownership data for the system, such as 

acquisition, depreciation, and warranty information. To 

set

 any of these fields, you must use the 

omconfig system assetinfo

 command. See "omconfig: Managing Components Using the 

Instrumentation Service."

omreport system events

Use the 

omreport system events 

command to view the current enabled or disabled SNMP traps. 

This command displays a summary of each component in your system for which events can be 
generated. For each component, the report shows which severities are set to be reported and which 
severities are set not to be reported. The following is an example output for a few components:

omreport system events

Current SNMP Trap Configuration

-----------

System

-----------

Settings

Enable: Informational, Warning and Critical

Disable: None

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

Icidu NI-707533 Manual Manual preview
NI-707533
Brand: Icidu Pages: 10
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual preview
RUGGEDSWITCH RS900G
Brand: RuggedCom Pages: 23
NEC P401-TMX4D User Manual preview
P401-TMX4D
Brand: NEC Pages: 2
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
Maipu SM3100-9TC-AC Install Manual preview
SM3100-9TC-AC
Brand: Maipu Pages: 26
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
Comnet CNGE28FX4TX24MS2 Installation And Operation Manual preview
CNGE28FX4TX24MS2
Brand: Comnet Pages: 154
IBM Redbooks Emulex VFA5 Product Manual preview
Redbooks Emulex VFA5
Brand: IBM Pages: 15
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Brand: 8e6 Technologies Pages: 76
SMC Networks SMCGS10P-Smart Installation Manual preview
SMCGS10P-Smart
Brand: SMC Networks Pages: 68
Ecos SECURE BOOT STICK FX Administrator'S Manual preview
SECURE BOOT STICK FX
Brand: Ecos Pages: 22
Cambium Networks cnPilot Home R200 Series User Manual preview
cnPilot Home R200 Series
Brand: Cambium Networks Pages: 136
Cambium Networks PTP 820S Technical Description preview
PTP 820S
Brand: Cambium Networks Pages: 208
Cambium Networks PTP 820C User Manual preview
PTP 820C
Brand: Cambium Networks Pages: 672
Digi TransPort WR11 XT Quick Start Manual preview
TransPort WR11 XT
Brand: Digi Pages: 4
Crestron Zum ZUMMESH-NETBRIDGE Quick Start preview
Zum ZUMMESH-NETBRIDGE
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands