manualshive.com logo in svg

Dell Command Line Interface, User Manual

The Dell Command Line Interface User Manual is a comprehensive guide that allows you to maximize the potential of your Dell products. With easy-to-understand instructions and troubleshooting tips, this manual is available for free download at manualshive.com. Access the power of Dell Command Line Interface and enhance your user experience today.

Share
Download
background image

136

Using the Storage Management Service

For example, the following 

omconfig

 command syntax for blinking a physical disk has three levels and 

three name=value pairs: 

omconfig storage pdisk action=blink controller=id pdisk=<PDISKID> 

where PDISKID=<connector:enclosureID:portID | connector:targetID>

In this example, the 

id

 in 

controller=id

 is the controller number such that controller 1 would be 

specified as controller=1.

Syntax for Required, Optional, and Variable Command Elements

The 

omreport

 and 

omconfig

 commands have multiple name=value pairs. These name=value pairs may 

include required, optional, and variable parameters. The following table describes the syntax used to 
indicate these parameters. 

Table 8-2.

Syntax For Name=Value Pairs For Parameters

Syntax

Description 

controller=id

Indicates the controller ID as reported by the 

omreport storage controller

 

command. To obtain these values, enter 

omreport storage controller

 to display the 

controller IDs and then enter 

omreport storage pdisk controller=id

 to display the 

IDs for the physical disks attached to the controller. 

For example, the 

controller=id

 parameter might be specified as 

controller=1

. 

connector=id

Indicates the connector ID as reported by the 

omreport 

command. To obtain this 

value, enter 

omreport storage controller

 to display the controller IDs and then 

enter 

omreport storage connector controller=id

 to display the IDs for the 

connectors attached to the controller.

For example, the 

connector=id

 parameter might be specified as 

connector=2

. 

vdisk=id 

Indicates the virtual disk ID as reported by the 

omreport 

command. To obtain this 

value, enter

 omreport storage controller

 to display the controller IDs and then 

enter 

omreport storage vdisk controller=id

 to display the IDs for the virtual disks 

on the controller.

For example, the 

vdisk=id

 parameter might be specified as 

vdisk=3

. 

enclosure=
<ENCLOSUREID>

Indicates a particular enclosure by specifying either 

enclosure=connector

 or 

enclosure=connector:enclosureID.

 

To obtain these values, you would enter 

omreport storage controller

 to display the 

controller IDs and then enter 

omreport storage enclosure controller=id

 to display 

the IDs for the enclosures attached to the controller. 

Summary of Contents for Command Line Interface



































































































































































































































Reviews:

No comments

Related manuals for Command Line Interface

4IPNET WHG301 User Manual preview
WHG301
Brand: 4IPNET Pages: 97
IBM 11a Quick Start Manual preview
11a
Brand: IBM Pages: 32
National Instruments NI 9871 Operating Instructions Manual preview
NI 9871
Brand: National Instruments Pages: 24
National Instruments NI 9478 Operating Instructions Manual preview
NI 9478
Brand: National Instruments Pages: 32
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
MikroTik RouterBOARD Groove Quick Setup Manual And Warranty Information preview
RouterBOARD Groove
Brand: MikroTik Pages: 4
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Allied Telesis AR725 Quick Start Manual preview
AR725
Brand: Allied Telesis Pages: 22
iBall Baton 150m Configuration Manual preview
150m
Brand: iBall Baton Pages: 9
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
CELOT CTR-180 User Manual preview
CTR-180
Brand: CELOT Pages: 34
Abocom WR5502 User Manual preview
WR5502
Brand: Abocom Pages: 63
Gemtek Systems WLTFQR-121 User Manual preview
WLTFQR-121
Brand: Gemtek Systems Pages: 51
RubyTech VS-820S User Manual preview
VS-820S
Brand: RubyTech Pages: 25
B&B Electronics EIP308 Product Information preview
EIP308
Brand: B&B Electronics Pages: 2
Patton electronics ipRocketLink 3086FR Quick Start Manual preview
ipRocketLink 3086FR
Brand: Patton electronics Pages: 12
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140

Brands by name

Popular brands

Load more brands