manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

451 

 

Command: config gratuitous_arp send periodically ipif System interval 5 
 
Success. 
 
DGS-3620-28SC:admin# 

 

36-7

 

show gratuitous_arp 

Description 

This command is used to display gratuitous ARP configuration. 

 

Format 

show gratuitous_arp {ipif <ipif_name 12>} 

 

Parameters 

ipif

 - (Optional) The interface name of the L3 interface. 

<ipif_name 12>

 - Specify the interface name. The maximum length is 12 characters. 

 

Restrictions 

None. 

 

Example 

To display the gratuitous ARP log and trap state: 

DGS-3620-28SC:admin#show gratuitous_arp 
Command: show gratuitous_arp 
 
Send on IPIF Status Up        : Disabled 
Send on Duplicate IP Detected : Disabled 
Gratuitous ARP Learning       : Disabled 
 
IP Interface Name : System 
        Gratuitous ARP Trap                     : Disabled 
        Gratuitous ARP Log                      : Enabled 
        Gratuitous ARP Periodical Send Interval : 0 
 
Total Entries: 1 
 
DGS-3620-28SC:admin# 

 

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

CZHOON CZH-T287 User Manual preview
CZH-T287
Brand: CZHOON Pages: 4
Moxa Technologies EtherDevice EDS-4009 Series Quick Installation Manual preview
EtherDevice EDS-4009 Series
Brand: Moxa Technologies Pages: 18
TP-Link TL-SG108E Installation Manual preview
TL-SG108E
Brand: TP-Link Pages: 2
Cablematic HUB-1230i User Manual preview
HUB-1230i
Brand: Cablematic Pages: 8
Omron D4N-1A20R Datasheet preview
D4N-1A20R
Brand: Omron Pages: 16
Grozone Control OSWDN User Manual preview
OSWDN
Brand: Grozone Control Pages: 20
Digitronic CamCon DC30 User Manual preview
CamCon DC30
Brand: Digitronic Pages: 24
Cypress CLUX-C61C Operation Manual preview
CLUX-C61C
Brand: Cypress Pages: 16
TRENDnet TEG-S41SX Specifications preview
TEG-S41SX
Brand: TRENDnet Pages: 2
W Box Technologies 0E-8P65W4POE Manual preview
0E-8P65W4POE
Brand: W Box Technologies Pages: 10
LevelOne FGU-5021 Quick Installation Manual preview
FGU-5021
Brand: LevelOne Pages: 15
3onedata IES2016-16T Series Quick Installation Manual preview
IES2016-16T Series
Brand: 3onedata Pages: 3
PCB Piezotronics IMI SENSORS EX686B77 Installation And Operating Manual preview
IMI SENSORS EX686B77
Brand: PCB Piezotronics Pages: 63
Leviton 47693-ESM Product Specifications preview
47693-ESM
Brand: Leviton Pages: 2
A SYSTEMS AV800HD User Manual preview
AV800HD
Brand: A SYSTEMS Pages: 80
Cabletron Systems SmartSTACK ELS100-24TXG Release Note preview
SmartSTACK ELS100-24TXG
Brand: Cabletron Systems Pages: 7
Elk Products ELK-M1DBHR Installation Manual preview
ELK-M1DBHR
Brand: Elk Products Pages: 2
Kramer VP-772T Quick Start Manual preview
VP-772T
Brand: Kramer Pages: 4

Brands by name

Popular brands

Load more brands