manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual, Page: 554 / 1170

Share
Download
D-Link xStack DGS-3620-52P Manual Download Page 554

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

549 

 

 

Example 

To enable the ND snooping function on the Switch: 

DGS-3620-28SC:admin# enable address_binding nd_snoop 
Command: enable address_binding nd_snoop 
 
Success. 
 
DGS-3620-28SC:admin# 

 

46-21

 

disable address_binding nd_snoop 

Description 

This command is used to disable ND snooping on the Switch. 

 

Format 

disable address_binding nd_snoop 

 

Parameters 

None. 

 

Restrictions 

Only Administrator, Operator and Power-User level users can issue this command. 

 

Example 

To disable the DHCPv6 snooping function on the Switch: 

DGS-3620-28SC:admin# disable address_binding nd_snoop 
Command: disable address_binding nd_snoop 
 
Success. 
 
DGS-3620-28SC:admin# 

 

46-22

 

config address_binding nd_snoop ports 

Description 

This command is used to specify the maximum number of entries that can be learned with ND 
snooping. 

 

Format 

config address_binding nd_snoop ports [<portlist> | all] max_entry [<value 1-50> | no_limit] 

 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments