D-Link xStack DGS-3620-52P Manual Download Page 835

Page: 835 / 1170

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide

830

74-14

delete pim6 static_rp group

Description

This command is used to delete a static RP.

Format

delete pim6 static_rp group <ipv6networkaddr>

Parameters

group

- Specifies the multicast group network address which will be removed from the static RP.

<ipv6networkaddr>

- Enter the IPv6 network address used here.

Restrictions

Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only
Command)

Example

To delete a static RP:

DGS-3620-28SC:admin# delete pim6 static_rp group FF1E::/64
Command: delete pim6 static_rp group FF1E::/64

Success.

DGS-3620-28SC:admin#

74-15

config pim6 embedded_rp state

Description

This command is used to set the state of the embedded RP.

Format

config pim6 embedded_rp state [enable | disable]

Parameters

state

- Specifies the embedded RP support in the PIM6 state.

enable

- Specifies that embedded RP support will be enabled.

disable

- Specifies that embedded RP support will be disabled.

Restrictions

Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only
Command)

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for xStack DGS-3620-52P

Reviews:

D-Link xStack DGS-3620-52P, Manual, Page: 835 / 1170

Search results

Summary of Contents for xStack DGS-3620-52P

Reviews: