Home
/
D-Link
/
xStack DGS-3620-52P
/
Manual

D-Link xStack DGS-3620-52P, Manual, Page: 725 / 1170

Share

Page: 725 / 1170

D-Link xStack DGS-3620-52P Manual Download Page 725

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide

720

Restrictions

Only Administrator and Operator-level users can issue this command.

Example

To disable SNMP linkchange trap support:

DGS-3620-28SC:admin#disable snmp linkchange_traps
Command: disable snmp linkchange_traps

Success.

DGS-3620-28SC:admin#

66-16

config snmp linkchange_traps ports

Description

This command is used to configure the sending of linkchange traps and per port control for
sending of change traps.

Format

config snmp linkchange_traps ports [all | <portlist>] [enable | disable]

Parameters

all

- Specify all ports.

<portlist>

- Specify a port or range of ports.

enable

- Enable sending of the link change trap for this port.

disable

- Disable sending of the link change trap for this port.

Restrictions

Only Administrator and Operator-level users can issue this command.

Example

To enable SNMP linkchange traps for ports 1 to 4:

DGS-3620-28SC:admin#config snmp linkchange_traps ports 1-4 enable
Command: config snmp linkchange_traps ports 1-4 enable

Success.

DGS-3620-28SC:admin#

«
...
723
724
725
726
727
...
»

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments