Home
/
D-Link
/
xStack DGS-3620-52P
/
Manual

D-Link xStack DGS-3620-52P, Manual, Page: 528 / 1170

Share

Page: 528 / 1170

D-Link xStack DGS-3620-52P Manual Download Page 528

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide

523

DGS-3620-28SC:admin# config ip_tunnel gre tn1 source 1.0.0.1 destination
1.0.0.2
Command: config ip_tunnel gre tn1 source 1.0.0.1 destination 1.0.0.2

Success.

DGS-3620-28SC:admin# config ip_tunnel gre tn1 ipaddress 2.0.0.1/8 ipv6address
2001::1/64
Command: config ip_tunnel gre tn1 ipaddress 2.0.0.1/8 ipv6address 2001::1/64

Success.

DGS-3620-28SC:admin#

To display the configuration of a GRE tunnel interface named “tn1”:

DGS-3620-28SC:admin# show ip_tunnel tn1
Command: show ip_tunnel tn1

Tunnel Interface : tn1
Interface Admin State : Enabled
Tunnel Mode : GRE
Ipv4 Address : 2.0.0.1/8
IPv6 Address : 2001::1/64
Tunnel Source : 1.0.0.1
Tunnel Destination : 1.0.0.2

DGS-3620-28SC:admin#

To configure a GRE tunnel (tunnel with: the name “tn2”, the delivery protocol IPv6, tunnel source
t

he IPv6 address 2000::1, the tunnel destination IPv6 address 2000::2, the GRE tunnel interface’s

IPv6 address 3001::1/64, the GRE tunnel interface’s IPv4 address 3.0.0.1/8):

DGS-3620-28SC:admin# config ip_tunnel gre tn2 source 2000::1 destination
2000::2
Command: config ip_tunnel gre tn2 source 2000::1 destination 2000::2

Success.

DGS-3620-28SC:admin# config ip_tunnel gre tn2 ipaddress 3.0.0.1/8
Command: config ip_tunnel gre tn2 ipaddress 3.0.0.1/8

Success.

DGS-3620-28SC:admin# config ip_tunnel gre tn2 ipv6address 3001::1/64
Command: config ip_tunnel gre tn2 ipv6address 3001::1/64

Success.

DGS-3620-28SC:admin#

To display the configuration of a GRE tunnel interface named “tn2”:

«
...
526
527
528
529
530
...
»

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments