manualshive.com logo in svg

D-Link xStack DGS-3620-52P, Manual

The D-Link xStack DGS-3620-52P is a high-performance switch designed for efficient network management. To help users get started, a Quick Installation Manual is available for download, free of charge, from manualshive.com. This manual provides step-by-step instructions for a seamless setup process, ensuring optimal performance of this innovative product.

Share
Download
background image

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide 

94 

 

syn

 - (Optional) Specify to synchronize sequence numbers. 

fin

 - (Optional) No more data from sender. 

udp

 - Specify that the rule applies to UDP traffic. 

src_port_mask

 - (Optional) Specify the UDP source port mask. 

<hex 0x0-0xffff>

 - Specify the UDP source port mask. 

dst_port_mask

 - (Optional) Specify the UDP destination port mask. 

<hex 0x0-0xffff>

 - Specify the UDP destination port mask. 

protocol_id_mask

 - Specify that the rule applies to the IP protocol ID traffic. 

<hex 0x0-0xff>

 - Specify that the rule applies to the IP protocol ID traffic. 

user_define_mask

 - (Optional) Specify the L4 part mask 

<hex 0x0-0xffffffff>

 - Specify the L4 part mask 

packet_content_mask

 - Specify the packet content mask. 

offset_0-15

 - Specify the mask for packet bytes 0-15. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 0-3. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 4-7. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 8-11. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 12-15. 

offset_16-31

 - Specify the mask for packet bytes 16-31. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 16-19. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 20-23. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 24-27. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 28-31. 

offset_32-47

 - Specify the mask for packet bytes 32-47 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 32-35. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 36-39. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 40-43. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 44-47. 

offset_48-63

 - Specify the mask for packet bytes 48-63. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 48-51. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 52-55. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 56-59. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 60-63. 

offset_64-79

 - Specify the mask for packet bytes 64-79. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 64-67. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 68-71. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 72-75. 

<hex 0x0-0xffffffff>

 - Specify the mask for packet bytes 76-79. 

ipv6

 - Specify the IPv6 mask. 

class

 - Specify the IPv6 class mask. 

flowlabel

 - Specify the IPv6 flow label mask. 

source_ipv6_mask

 - Specify the IPv6 source IP mask. 

<ipv6mask>

 - Specify the IPv6 source IP mask. 

destination_ipv6_mask

 - Specify the IPv6 destination IP mask. 

<ipv6mask>

 - Specify the IPv6 destination IP mask. 

 

Restrictions 

Only Administrator, Operator and Power-User level users can issue this command. 

 

Example 

To create CPU access list profiles: 

DGS-3620-28SC:admin#create cpu access_profile profile_id 1 ethernet vlan 
Command: create cpu access_profile profile_id 1 ethernet vlan 
 
Success. 
 

Summary of Contents for xStack DGS-3620-52P



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for xStack DGS-3620-52P

D-Link SmartPro DGS-1500-20 Reference Manual preview
SmartPro DGS-1500-20
Brand: D-Link Pages: 113
D-Link xStack DGS-3120 Series Cli Reference Manual preview
xStack DGS-3120 Series
Brand: D-Link Pages: 1150
KE2 20543 Quick Start Manual preview
20543
Brand: KE2 Pages: 4
Eaton Pow-R-Line SPX0361126 Maintenance Manual preview
Pow-R-Line SPX0361126
Brand: Eaton Pages: 584
Gefen 2X2 VGA SWITCHER User Manual preview
2X2 VGA SWITCHER
Brand: Gefen Pages: 12
Edge-Core AS9926-24D Quick Start Manual preview
AS9926-24D
Brand: Edge-Core Pages: 12
Hamlet XUSB370MS User Manual preview
XUSB370MS
Brand: Hamlet Pages: 2
ICCN WX7020-1210G Web User Manual preview
WX7020-1210G
Brand: ICCN Pages: 48
Advantech EKI-2525P User Manual preview
EKI-2525P
Brand: Advantech Pages: 28
LEGRAND Pro 21 7756 28 Manual preview
Pro 21 7756 28
Brand: LEGRAND Pages: 197
Valcom V-2971 Connections preview
V-2971
Brand: Valcom Pages: 1
Duxbury Networking N.JGS516PE-100EUS Installation Manual preview
N.JGS516PE-100EUS
Brand: Duxbury Networking Pages: 4
IMC Networks Giga-AcessEtherLinx-II Operation Manual preview
Giga-AcessEtherLinx-II
Brand: IMC Networks Pages: 40
Scion-Tech SC01.7050 User Manual preview
SC01.7050
Brand: Scion-Tech Pages: 9
Exsys EX-1190HMVS-PD Manual preview
EX-1190HMVS-PD
Brand: Exsys Pages: 14
Black Box Peripheral Sharer 2 to 1 Manual preview
Peripheral Sharer 2 to 1
Brand: Black Box Pages: 35
Comprehensive CSW-VGA212 User Manual preview
CSW-VGA212
Brand: Comprehensive Pages: 6
AMX AVS-OP-2404-210 Specifications preview
AVS-OP-2404-210
Brand: AMX Pages: 1

Brands by name

Popular brands

Load more brands